Mauro

Comments

• I solved my problem.I set DtrEnable = True and RtsEnable = True of the serial port and the communication works perfectly!Greetings

  in serial communication Comment by Mauro February 2022
• Good morningV2 runs on RUMBA32 and communicates perfectly with Repetier-host. The printer works very well. My application communicates with V1, but fails with V2. I sniffed the data traffic on the com port with "Serial Port Monitor" and it is clear …

  in serial communication Comment by Mauro February 2022
• The firmware compiles and works perfectly.The TMC5160 driver is not working, but I believe it is dead.Thank you

  in STEPPER_TMC5160_HW_SPI con dev2 Comment by Mauro December 2021
• Grazie. Adesso il firmware si compila correttamente. Non riesco a far funzionare in mio TMC5160, ho controllato con oscilloscopio i segnali di RUMBA 32 e mi sembrano OK. Credo a questo punto che sia guasto.

  in STEPPER_TMC5160_HW_SPI con dev2 Comment by Mauro December 2021
• Goodmorning everyone. I resumed the configuration with a new MKS-RUMBA32.I re-installed Repetier-Host and now I see the EEprom values ​​in the "EEPROM firmware settings" window.Now after a long time I cannot find the solution to this problem: at the…

  in MKS_RUMBA32 end dev2 Comment by Mauro November 2020
• Thank you Unfortunately when I added the Z motor driver, something I didn't understand blew up the STM32 and RUMBA32 died !!For now until I get a new RUMBA32 I can'tshow my log of the M205 command.

  in MKS_RUMBA32 end dev2 Comment by Mauro October 2020
• OK thank you very much If I send M205 from the log I see the EEProm values, but from the Repetier_Host "EEPROM firmware settings" window I don't see anything, it's all white.Do I need to reinstall Repetier_Host?

  in MKS_RUMBA32 end dev2 Comment by Mauro October 2020
• EEPROM_MODE 0 was only set at the end, I didn't know what else to try. Previously EEPROM_MODE 1 was set, but the EEProm values are not read from Repetier_Host. Axis X is the first configuration of the whole machine, but I have big problems.

  in MKS_RUMBA32 end dev2 Comment by Mauro October 2020
• Good morning I have tried many times to change the value of HOMING_FEEDRATE_X in Configuration.h and rewrite the firmware, but with no effect. In Retetier_Host the window showing EEProm values is empty and without values.

  in MKS_RUMBA32 end dev2 Comment by Mauro October 2020
• OK thanks

  in V2 firmware on MKS rumba32 Comment by Mauro August 2020
• Good morningWhich VID and PID should I use, that of the STM32 BOATLOADER or the COM port? Now I get these errors: > Executing task: C:\Users\mauro\.platformio\penv\Scripts\platformio.exe run 3D Printer control boardHARDWARE: STM32F446RET6 180MH…

  in V2 firmware on MKS rumba32 Comment by Mauro August 2020
• Thank you

  in I have enabled CNC milling support. #define SUPPORT_CNC 1 #define CNC_WAIT_ON_ENABLE 300 #define CN Comment by Mauro January 2018
• Grazie

  in I have enabled CNC milling support. #define SUPPORT_CNC 1 #define CNC_WAIT_ON_ENABLE 300 #define CN Comment by Mauro January 2018
• thanksNow I do not get any compilation error.

  in I can not compile the firmware Comment by Mauro May 2015
• thanksStill I get the second error: HAL.cpp:1176:28: error: attempt to use poisoned "SIG_USART1_RECV"  #define SIG_USARTx_RECV   SIG_USART1_RECV

  in I can not compile the firmware Comment by Mauro April 2015
• thanksI await the release of new firmware.Arduino 1.0 does not work on my PC, only 1.6.3

  in I can not compile the firmware Comment by Mauro April 2015