unf0rg0tt3n
About
- Username
- unf0rg0tt3n
- Joined
- Visits
- 16
- Last Active
- Roles
- Member
Comments
-
Okay that worked with mine too. Only eeprom 0 gave errors. Did yours serial connect?
-
RAyWB said: ok...i use 1.0.3 that might be the compile problem. can you upload your complete repetier folder somewhere ? i have to leave now but in later evening i´ll find some time to test on a spare due/radds Did you had time to check…
-
RAyWB said: ok...i use 1.0.3 that might be the compile problem. can you upload your complete repetier folder somewhere ? i have to leave now but in later evening i´ll find some time to test on a spare due/radds That would be so great if…
-
Btw with a baudrate of 250000 it got this in repetier: 11:35:30.892 : start 11:35:31.048 : N1 M110*34 11:35:31.048 : N2 M115*36 11:35:31.048 : N3 M105*36 11:35:31.048 : N4 M114*35 11:35:31.048 : N5 M111 S6*98 11:35:31.064 : N6 T0*60 11:35:31.064 : N…
-
So by change eeprom mode to -1 it actually works.Gives me: start Info:PowerUp In the serial monitor output
-
Comes with an instant error in printer.h at line:#if FEATURE_RETRACTION Com::config(PSTR("RetractionLength:"),EEPROM_FLOAT(RETRACTION_LENGTH)); Error:Arduino: 1.8.5 (Windows 10), Board:"Arduino Due (Programming Port)" sketch\Printer.cpp: In sta…
-
RAyWB said: just to be shure : you put the radds on the due before running the i2c scanner? Yes, not sure if i did the thing right.Uploaded repetier to due, then I uploaded the i2c scanner. Was that right?
-
RAyWB said: first check if due works, try blink sketch from arduino. remove radds for that testif test is ok , reinstall radds and load I2c scanner (https://playground.arduino.cc/Main/I2cScanner)then you should see eeprom address on arduinos …
-
RAyWB said: try to remove radds board and upload arduinos blink sketch, see if that works. as you wrote before you fried something ... may be eeprom on radds is broken what would result in non booting Yeah, but it was on the raspberry pi…
-
Damn it's just, it worked before, like a charm but now it doesn't. So now I will unplug everything and gradually build up until something fails; which will be a labour intensive job. Thanks for all your help!
-
It does really nothing at all. But I never had that serial monitor working. My settings are:
-
So, I tried 4 different scenarios.1) use the connection without the PSU turned on 19:24:40.713 : No start signal detected - forcing start 19:24:40.728 : N1 M110*34 19:24:40.728 : N2 M115*36 19:24:40.728 : N3 M105*36 19:24:40.728 : N4 M114*35 19:24:4…
-
RAyWB said: the red one on Due is same function as black one on radds.is your radds board mounted on arduino during your test? Everything is mounted. I thought the red button was the wipe button So I attach my laptop to the due (with…
-
RAyWB said: so you seem to have Due Clone, not original one.some of them need a fix on 16U2 serial converter. It is an original since it came in the original arduino box from a arduino certified seller. The think is it worked before in my…
-
RAyWB said: which micro usb port do you use? the one near power supply connector or the other one? what happens if you press the arduino reset button? (keep repetier host connected) I'm using the one near the power supply connector. The r…
-
RAyWB said: Might be I´m wrong , as Controller 7 is the radds extention board,tot related to display. what´s the exact message on repetier host? wait? or 1 command waiting? if 1command waiting try to set eeprom mode to 2 and upload firmware a…
-
RAyWB said: as you have no display you have to set #define FEATURE_CONTROLLER 0 (actually it´s set to7) rest looks ok on first sight Thanks! Does this have any influence on the not connecting? Just don't get why it will connect with th…
-
RAyWB said: if firmware is setup correct , usually not.your complete configuration.h would be useful here it is: https://pastebin.com/Eqhr0mHi
-
Do I also need a screen to be installed? Because I don't have one.
-
did that, also for octoprint. Both won't work.Tried to use both microusb ports
-
RAyWB said: Is your Baudrate set correct? It's set to: // ################# Misc. settings ################## #define BAUDRATE 115200 Is this correct?
-
Okay wow! So, i rewired E0 and now E0 and E1 are fully functional without ticking thanks for all the help you guys!!!
-
Repetier said: > Extruder went on X and turned quite well. So motor/cable then look good. > When attaching Extruder to X it worked but still the ticking. Confusing statement. I thought the ticking was the error, so how can it work t…
-
Repetier said: Try x motor on extruder socket to test if motor/wires are the problem. Tried to swap out the wiring.Extruder went on X and turned quite well. When attaching Extruder to X it worked but still the ticking.
-
Also tried to adjust the V-ref and microstepping count. Also no luck
-
MartinH said: What drivers are you using? What microstepping? You have some large numbers in your config regarding steps/mm and max feedrate, maybe try reducing the max E feedrate see if any different. Hi MartinH, I am using the RAPS128 …
-
Repetier said: Send lower feedrate when extruding/testing. G92 E0 G1 E30 F60 will extrude at 1mm/s for 30 seconds. That is slow. It might also be a broken wire instead of contact. Or stepper driver is defect. You can find this easily by swa…
-
Repetier said: Assuming there are no forces required to move the extruder it looks like one motor coils gets no current. Often just a contact is bad when this happen. To be sure try to move much slower and see if it still happens. How to …
-
On the duplicator it was always X max if i recall correctly. To be sure I always can ad an additional endstop for min just to be sure? Next on my list is getting the heaters to work. It now gives decoupled error.
-
RAyWB said: before you wrote z is moving down... now you write z-is moving up....??????? so you have to rotate both z motor connectors again , lets do it step by step if you want to home x to the left side you have to move endstop to the l…