unf0rg0tt3n
About
- Username
- unf0rg0tt3n
- Joined
- Visits
- 16
- Last Active
- Roles
- Member
Comments
-
phamyen said: Thanks for sharing this marvelous post. I m very pleased to read this article. happy room Dude, no.. just no
-
Repetier said: Slot should work when you have no display selected. Then it uses default sd ss pin which is configured to be the one on the board. file system is vfat32. Sd card must support spi interface. Not sure what the maximum supported s…
-
I don't know what made it work but I think the software endstop did the trick because it isn't crashing in the bed. All works now!
-
That worked. So when disabling the hardware zmin endstop as the guide says in the probe manual on the website; it won't stop anymore when it reached the bottom. Why is that?
-
MartinH said: #define Z_PROBE_X_OFFSET 0 #define Z_PROBE_Y_OFFSET 0 These need setting according to the offset distance of probe to nozzle Wiring worked, the offset X and Y .. are those calculated from extruder 0 or 1 or do I need to defin…
-
MartinH said: #define Z_PROBE_X_OFFSET 0 #define Z_PROBE_Y_OFFSET 0 These need setting according to the offset distance of probe to nozzle I know, but thanks for the reminder. I still am doing the wiring and proper testing with the volta…
-
Repetier said: Ok, no idea why he used a servo pin for it, but has nothing to do with servo. As I said pins may have names but get function you assign, so any free pin works. Only important is that it is configured as input and you do not exc…
-
Repetier said: z min endstop switch makes only sense with a leveled bed. If you want to allow it not leveled you need to remove it. You have 2 options. Use z probe as z min pin as well or use z max homing. z max homing has some benefits but…
-
Working!
-
RAyWB said: so if you swap 2 and 3 in cable on radds side this motor should also work Yes, All works now! really smooth and well thanks!Now I'll need to finish up with the touch screen and such and then I'll post a picture of the fini…
-
Really strange... The working stepper has 1-2 as coil and 3-4 as coil.On the other hand the non working stepper has 1-3 as coil and 2-4 as coil.For the non working stepper it makes a lot of sense that it doesn't work since the coils are working aga…
-
RAyWB said: can you upload a pic of the not working motor?(connector and nameplate) Sure: and nothing modified, straight out of the box
-
Nope, but I did use the same wire on 2 other steppers those worked.I also tried the E0 and E1 pins; that didn't workI used 3 different wire sets also that didn't work. The only stepper not working is the second stepper in my video.The first stepper …
-
Yes one of the steppers is working as seen in the video
-
Got the steppers going the right direction again.E1 still is stuck.another stepper, same port: By my guess my stepper got broke or the V-ref is not set properly because it's on 1.6V and stepper is rated at 1.8V
-
Thanks! I won't unplug anything from a running system that's how I am raised
-
Yes! the heaters are heating, the X, Y and Z steppers work but in the opposite direction So I have to swap the wiring again nothing special. the stepper is making a machine gun sound like it's choking on something, but I had that before, so easy t…
-
RAyWB said: Ok, unusual but if you are shure it´s okdid you check the red fuse? may be you can borrow one in your neighbours car ;-) Okay, I'm officially retarded.Checked again, unplugged the wires, followed them and...
-
RAyWB said: well , following the red and black wires are they power supply for both sides ?in that case what´s the brown and black wire?are you shure you didn´t swap something? Red fuse:Red and black --> PSU Blue fuse side:Red and Bl…
-
RAyWB said: there are green led´s near fuses these should lbe illuminated.maybe check the fuses (the red one is for the motors) can´t see it in the video as the stepper wires block view I've got the images right here: As you see no ligh…
-
RAyWB said: did you connenct both power supply inputs on the radds?one is for the motors , extruders and fans, the other one only for heatbed Yes both at the left and the right side.But at the right side that amber light is on. Something…
-
Repetier said: Yes, that sounds like a defect thermistor or a short/break in wire. The wire works, no error messages!But it still doesn't work; The X,Y and Z axis are still not reacting. None of the stepper motors are reacting. Here you ca…
-
It's the actual thermistor, I hope faulty wire since i made it longer once.I hooked up thermistor 0 to thermistor port 1 and it gave working.When I hooked up thermistor 1 to port 0 it gave defect.
-
It almost works, I have to fight the amber LED before it'll get out of dry run mode: https://i.imgur.com/Huv43xg.jpg Edit: extruder 0: working extruder 1: temp sensor defect heated bed: working So a defect temp sensor; Does i…
-
Not even the wires are the problem, first try and it didn't work: https://imgur.com/a/A6SfueJ the board makes contact with the little rings. after that it immediately stops connecting
-
Repetier said: Just add wires - always a few and test - until it stops working. Then you know where it was. I'm going to, but this means my board is OK right? just to be sure
-
So... I am a freakin retard! I was so done that I started packing the shit board, when I thought: "Okay everything is loose and what do I have to lose"; I hooked it up directly to my computer, wrote the whole sketch and connected the DUE with RADDS …
-
RAyWB said: well, i´m in germany , but if you have good soldering skills you can change the eeprom yourselfor you have somebody to change it for you, that´s -a EEProm costs lower than 1 Euro... -b would be something like this :https://www.…
-
RAyWB said: May be you give this solution a try and erase eeprom with the arduino sketch from here : https://forum.repetier.com/discussion/5850/ruramps-v1-3-and-repetier-v1-0-4dev-work-only-without-the-eeprom-enabled#latest seems to be simil…
-
RAyWB said: on 250000 baud as its in your configuration.h,for eeprom 0 (no eeprom) please set feature retraction to 0 as this feature needs eeprom. so please try 1st : eeprom 0 without feature retraction for serial connection 2nd : eeprom …