RAyWB
About
- Username
- RAyWB
- Joined
- Visits
- 2,124
- Last Active
- Roles
- Member
Comments
-
das was ich jetzt so sehe schaut i.O. aus Lt.der Konfiguration sieht das so aus : ein Thermoelement auf über den im Board eingebauten AD495 auf THERMOCOUPLE_0_PIN und steuert den Lüfter,ein Thermoelement über externen AD 8495 auf THERMOCOUPLE_2…
-
Hab mir mal den Schaltplan vom Board organisiert , A8 und A9 von der Stiftleiste EXTTC gehen ohne Umwege zum Controller,sollten also für deine AD8495 funktionieren wenn die Firmwarekonfiguration stimmt.Wenn Du die Configuration.h hier teilst kann ma…
-
dann scheint mir aber eher die Leitungsverlegung die Ursache zu sein.Wenns mit den Thermistoren ging und mit den Thermoelementen nicht mehr ist das recht plausibel.In der Nähe der Thermoelementanschlüsse am Mainboard sitzt ein kleiner IC mit 8 Pins,…
-
P.S. Thermoelemente und deren Leitungen sind extrem empfindlich , Verlängerung der Leitungen niemals mit Kupferund niemals löten , dafür gibts spezielle Thermoleitungen und Stecker. das macht das ganze auch teuer.Ist ja ganz Nett was so im Handel an…
-
irgendwie reden wir sowas von aneinander vorbei....mit was du immer so machst meinte ich die firmware über configtool oder github.wegen der beschaltung frag doch einfach bei reprapworld an, die haben das entwickelt.
-
siehe oben : laut Datenblatt sind die Thermocouple pins (Stiftleiste EXTTC) auf A8 und A9. und was machst du immer so?
-
lies einfach mal den link von dem Board komplett durch da sind doch die Pinnummern tabellarisch angegeben.Die für Dich relevanten sind auf Seite 10. Wie hast du die Firmware geladen ? Über github oder von hier :https://www.repetier.com/firmware/dev/…
-
Vielleicht hilft das weiter: https://reprapworld.com/documentation/datasheet megatronicsv3.pdf laut Datenblatt sind die Thermocouple pins (Stiftleiste EXTTC) auf A8 und A9. in der Firmware in der config.txt entsprechend eintragen bzw. im configtool …
-
as far as I´m informed it depends on windows , windows7 doesn´t support that feature.
-
remove this line :(back to start) dtoverlay=pitft35-resistive,rotate=90,speed=20000000,fps=20 (added this line later to see if it has an impact, but it does nothing no matter what value I use) modify this line: dtoverlay=waveshare35a to: dtoverla…
-
can you share a copy of your config.txt?
-
if you installed the screen as written above you have to change rotation in config.txt this line : dtoverlay=pitft35-resistive,rotate=90,speed=20000000,fps=20
-
Exactly, i´m a long term user of Repetier Host on WIN7 and WIN10 without problems caused by Repetier .My Problems were caused to 99% by the guy sitting in front of my computer.Anyway, Keep in mind RepetierHost , included Slicers and also Repetier Fi…
-
@Repetier may be this also helps https://www.raspifun.de/viewtopic.php?t=4 scroll to (3)
-
in configuration.h look for : #define UI_REVERSE_ENCODER 0 if 0 change to 1 or if 1 change to 0 that should fix the issue
-
as far as i know there is no way , at least not an easy one.a hard one would be to write down all values and tags shown in eeprom editor and set up a new one usingthe configuration tool , but I´m pretty shure you will not get a running firmware in …
-
strange...from data log firmware should be repetier 92.9 ... in that case the attached firmware does not match to data log
-
The firmware you attached is Marlin ....it´s not Repetier Firmware so sorry, i can´t help you.
-
you have to upload your files to a place you want (f.e. Google drive) and just place the link here.
-
look at your configuration.h there should be some lines like : #define LANGUAGE_DE_ACTIVE 1 // German#define LANGUAGE_EN_ACTIVE 1 // English 1 means language gets compiled in , 0 means not select the language you wan…
-
Repetier said: Did you also test if sudo rfkill unblock wifi changed anything especially sudo nmcli dev should go to disconnected or connected afterwards. same problem here, sudo rfkill unblock wifi didn´t change anything wlan0 still unan…
-
maybe this helps to find direction?https://forum.repetier.com/discussion/comment/27368/#Comment_27368
-
sorry, i can´t help out for marlin FW as i never used that stuff.(I´m repetier user from the bone ;-) )isn´t there a marlin forum ? btw ... wouldn´t be a simple way just to split the gcode into several files ? (1 file for each bit)
-
regarding M0 see :https://reprap.org/wiki/G-code The Marlin Firmware does wait for user to press a button on the LCD, or a specific time. "M0 P2000" waits 2000 milliseconds, "M0 S2" waits 2 seconds. that explains why it stops at M0 respectivel…
-
see here:https://forum.repetier.com/discussion/comment/25652/#Comment_25652
-
seems you are loosing steps .check Motor current https://www.derpade.de/3d-drucker-a4988-motortreiber-stromstaerke-einstellen/next : try to reduce acceleration to 100 , iand then increase from there
-
ok, so M05 is spindle stop,M00 is machine stopand M03 is spindle start. as far as i know that´s just something like a workaround for a real m6... the minor problem is that repetier does not understand the m00. what about z-correction for different t…
-
seems that lines cause Trouble :G1 X185.9164 Y276.5839F600.000000you need a space between y coord and Fshould look like:G1 X185.9164 Y276.5839 F600.000000 the code you posted has several lines like that.another point could be the warmup Setting of l…
-
Can you post a gcode section to see what Estlcam generates for tool change?
-
for GUI it should be possible to use EVENT_UI_OVERRIDE_EXECUTE to redefine UI_ACTION_LIGHTS_ONOFFsee events.h