Zogar
About
- Username
- Zogar
- Joined
- Visits
- 33
- Last Active
- Roles
- Member
Comments
-
Creality k1 family uses Klipper in the background. can't either?
-
In the Gcode list of the project I cant. They are sorted by name. https://ibb.co/Qcg4CGk
-
STM32CubreProgrammer says Start Addres: 0x08000000
-
Klipper 0.12 Python3 always fails ###### Updating python virtual environment ###### /tmp/klipperInstaller.sh: line 143: virtualenv: command not found Only works if you... Install Klipper 0.12 Python2 and fail..., then retry Klipper 0.12 Python2 and…
-
Solved with sudo -icd /optrm -r klipper from: https://forum.repetier.com/discussion/11473/printer-deletion-failed-undefined
-
Same problem here. Im trying to install klipper but this fails and now cant delette printers. Printer Deletion Failed Undefined. [21.02.2024 00:51:45] : Handling action 'getKlipperStatus' caused error boost::filesystem::directory_iterator::construc…
-
Flash menu icon doesn't show every time. Why?
-
The problem seems to ocurr when I edit some files and then I try to re-edit recently edited files. Same file, updated and not updated in Firefox Vs Repetier Server Monitor. https://youtube.com/shorts/4Rvhu5IunCE
-
but that is often not the case Except you have a farm. I print same files everyday. xDStill, I get the point that implementing an optimization here on something that's relatively unobtrusive isn't justified.
-
I came here to suggest the same thing and found that someone did it before me. A code editor is required for the files in the library. Downloading, editing and re-uploading them, especially if there are several of them, is a tedious task. My goal…
-
I use RaspberryPi.
-
Ok, I get something like that. This are from https://teachingtechyt.github.io/calibration.html#speed After what you comment, I think that the bottleneck is in the printer board that cannot process so many instructions per second. I managed t…
-
Thanks!
-
In some files I have to lower the print speed to 80% for the seam to print correctly. Same thing on 10 printers. The slicer from the cell phone is a bit annoying. Playing 80 would be easier.
-
All is OK. Strange... I will wait for next release to upgrade...
-
failed: Temporary failure in name resolution. wget: unable to resolve host address ‘download3.repetier.com’ If I acces from my computer says 404 page not found
-
To be sure... Some printers like Ender 3 or Artillery x1 do not allow saving in Eeprom. So to modify this, I have in the beginning of my files the acceleration and speed settings that I prefer. (This is a CURA legacy, before using repettier server)…
-
I have great news. Replace code works.I did not realize it because the speed is not updated in the interface. But yesterday I put the same file to print on two different machines and one finished before the other. So it works ... I don't know if…
-
I try that and not work.https://ibb.co/dtsngDF Can you check that on your test setup?
-
I try thishttps://regex101.com/r/zAHjvR/1 Regular Expresion: /M220 S100 ;Reset Feedrate/g Gcode to executeM220 S80 ;FEEDRATE 80 Personalizado https://ibb.co/68hPzVp this matches on regex101 https://ibb.co/0sS2cJR But not work. for this Gcode M1…
-
Repetier said: > What I have noticed is that after a few weeks, apparently the license has been lost leaving the installation blank. I had to enter the menu and activate the license again to restore everything. Do you mean there is no lice…
-
Me again. The problem persists on my Raspberry Pi 3 and 4. What I have noticed is that after a few weeks, apparently the license has been lost leaving the installation blank. I had to enter the menu and activate the license again to restore everyth…
-
For my without realtime view is good. I use it to control nozzle without need to scrol between menus in the printer. Generally the problem is I use the control tab without print active and all is fine, but when I will go back with a print active t…
-
I m pro user. The licence key are ON. I went to check the latest version of the software and it was able to connect successfully. It runs on a Wi-Fi connected raspberry pi 3. Repetier 1.2.0 I will restart the server when prints finish. I will keep y…
-
Could you put a control to activate or deactivate the drawing in real time? Maybe this helps.
-
The problem happens when you send to print from the library. It is 1 second, right at the moment where it finishes processing and loads the job in the printer. I have configured to download heavy work on my desktop pc, but on my pc the version is ol…
-
But you can't bulk add files to an existing project
-
I recommend USB 3.0 Hubs with external source power 5V 3A. And cover VCC pins in usb plugs to printers to not drain unnecessary power. I have 7 printers with that. Some usb hubs habe switches to cut off power on each plug.
-
What is the variable for Repetier Server to place the last Z position? G92 Zxx xx?