rim
About
- Username
- rim
- Joined
- Visits
- 7
- Last Active
- Roles
- Member
Comments
-
Ok. So what is the solution to solve the problem I have? Any suggestions please? Because I try to find something in the net that can help me to solve this, but no luck and not much about the RADDS Card !
-
RAyWB said: "The operation voltage for the drivers is ~3V" nope, the voltage you use to supply the radds card is also operation voltage for the drivers "searching in the net I found out that most of makers don't advise you to do it" well..no …
-
The operation voltage for the drivers is ~3V Now, what doesn't make since to me how the big printers that use the same thing two stepper motors NEMA23 with the same specifications or more are drived? Is it possible to use an external Microstep Dr…
-
Hello, Can u help me about this please: I have four NEMA23 Stepper Motors 2303HS200AW-175oz-2.00A And one NEMA23 Stepper Motors 2315HS300AW-345oz-3A. My question is how to adjust the right current. Because when I saw the documentation and I arrive…
-
Ok. I'll check that and come back to you. And thank you for your help.
-
RADDS Power Stepper Driver (RAPS128 ) Motors: NEMA 23 Stepper motor (Rated current 2A) To set motor current shall I use this command:? M906 X2000 Y2000 Z2000 (mA), because I did it and I don't know if it was set or not... When I use multimeter tha…
-
Hello Repetier and RAyWB, Thanks for your quick responses. I tried what you told me, but no luck. I did my calcul and used higher Feedrate values. But no movement, only a sound made by the motor : / So I wanted to redo everything and here's what ha…
-
RAyWB said: How did you change the setting?Just by new Firmware upload or did you change via eeprom editor? That was just by EEPROM.
-
I changed the value, all what happened is just now when I send G1 X 10 it moves so slowly and the distance didn't change (still have the same problem)
-
Thank you very much RAyWB I'll test that and come back to u )
-
I didn't get what u really do mean about this "Often it is with power of 2 as microsteps can add a multiplier like *2, 4, 8, 16, 32, 64, 128 and 256." . Can you help me more about what shall I do please... These are my steps/mm #define XAXIS_STEPS_…
-
Me again. Sorry for asking too much questions. About the print area of my 3D printer. I still have the same problem it doesn't give me the right dimensions! I've modified the dimensions in EEprom but still have the same essue. But my problem is tha…
-
13:00:38.203 : info:Continue from fatal state13:00:38.207 : important:Extruder jam detected13:00:38.207 : Info:Marked all extruders as unjammed.13:00:38.211 : Jam control disabled:113:02:23.224 : DebugLevel:1413:02:23.241 : Error:One heater seems de…
-
Ok. What about this error : "Notification: Heater decoupled" In Firmware I found this: At first this is what I had: #define DECOUPLING_TEST_MAX_HOLD_VARIANCE 20 // I increased this to 40 But I still have the same problem...
-
Ok. Thank you. Problem solved. It was because I choosed an extruder designed socket for second Z motor. Now that the problem is solved. I have one other issue the extruder turn so slow! Here is what I did in the configuration: #define EXT0_MAX_FEEDR…
-
Can you please explain to me this When I try to home the Z axis the motor of the extruder turns at the same time and it turns in the right direction now. But, when I try to turn the extruder alone it just start vibrating! My questions are: 1) why…
-
No I have not a filament sensor. I tried to switch some cables.No luck with that! As I changed where I pluged the RAPS of the exdruder and I put it into EXT0, no luck too! Here is all what I did. // ################ END MANUAL SETTINGS ############…
-
Now it works, but I have another problem! When I try to load and extrude 100mm of filament. When I send G92 E0 than G1 E100. The extruder starts to load the filament at the same time it starts to unload it! I don't know where the problem is and b…
-
It didn't work. Still shows like the extruder is Off
-
Ok. Thank you very much.I'll try that
-
Thank you very much for ur help.It works now
-
Hello, I have some issues about my mechanical Endstops. I tried evrything but with no success. When I home the axes, It just doesn't stop , they heat the endstop. Any help please! Repetier Firmware: // ################ Endstop configuration #####…
-
Ok. Thank you. One other question please about the ensdtops. I have a mechanical endstop V1.2. Belows whats I did in the program. My problem is that the endstops doesn't stop the axis! // ################ Endstop configuration #################…
-
Hei, I have a question please. This is the size of my bed: #define X_MAX_LENGTH 250 #define Y_MAX_LENGTH 250 #define Z_MAX_LENGTH 250 But it doesn't seem like that when I move my axis...!It's like it consider it 90 x 90 x 90! Could it be some…
-
Me again... X, Y and Z finally worked But now I have another problem. When I turn on the printer, the Z axis starts to go up without even touching anything !! Do you have any idea what may be causing this?. Thank you
-
Okey.Thank you. And why Z can't move up when I activate the E-HALL Endstop max?
-
Hello, below everything I did in the config. But as I said before, no movement of the two steppers of Y and that of X! 1) The Y axes make noise as if they move the axes, but no rotation / no movement only a sound !! 2) The X axis is identic…
-
Yes they are serious. Because I'm using a lead screw drive system. X --> I shoosed 64 step/mm (200 X 64)/1.25=10240 Step/mm Y--> 32 step/mm (200 X 32) / 1.25= 5120 Step/mm And Z : same like X 64 step/mm (200 X 64)/1.25=10240 Step/mm
-
Hei, I've took ur program and all I changed is the steps/mm I put (X:10240; Y:5120; Z: 10240, E:476,5), the type of the sensor and mirrors of Y and Z axies. Z: is okey. Y: It makes a sound like it's turning but no move not rotation. X: tries t…
-
Hello again, I've tested the program, and this is what happens: X: Makes a strange sound, and it moves only one step and stop. Y: The motors just vibrate without turning. Z: After switching the cables, it works. But when I started testing Y axis…