MShievitz
About
- Username
- MShievitz
- Joined
- Visits
- 135
- Last Active
- Roles
- Member
Comments
-
For the invalid moves question you need to find the "minimum squares" solution for the printer radius in question before that will work correctly. example:my print surface is a pyrex disc 90mm in RADIUS.my print radius is 70mm radius. on that disc.t…
-
Well the bed does not flex, it's glass, but it's mounted on rubber discs that do compress. What you are suggesting might be the best way to go. But right now it's trying to level in the air. When I have been able to get it in contact with the bed, i…
-
GT2560_sch.zip
-
this is the GT2560 schematic link
-
i have this board, my daughter is using it for a science project.it will run with 'repetier choose amtel 8 processor/ultimaker shield 1.5.7' display (forr her particular delta) 'smart controller from reprapdiscount on ramps or rumba' will compile an…
-
when i attempt a g29 map it seems to start at an odd offset (too close to x0, y0). what controls the start point of the grid. i assume its the grid radius chosen on the first page of the web config. these coordinates appear to relate to delta inver…
-
i would like to have the probe start further from the bed, probe down then back up for travel. my current build seems to travel on the bed then pop up to take a measurement. this is causing the head to crash at the outside edges of the bed. do i hav…
-
Thank you. important information. i have my delta built and measured pretty well, but i am still having problems with auto leveling with an inductive probe setup. I could use some clarification on a few things: Variables that affect probe and head …
-
also how do i retrieve the distortion map data from the eeprom. i have a program that will visualize the data. it is asking for the g29 data 7 rows of 7 values.
-
OK, i am going to check all values again, in the meantime i have an inductive probe set up now, it triggers fine, but i could use some help understanding the EEPROM values. The probe is functioning, it triggers at 1.79z, will go low again at 1.99z a…
-
< 10:05:03 AM: FIRMWARE_NAME:Repetier_0.92.3 FIRMWARE_URL:https://github.com/repetier/Repetier-Firmware/ PROTOCOL_VERSION:1.0 MACHINE_TYPE:Delta EXTRUDER_COUNT:1 REPETIER_PROTOCOL:3< 10:05:03 AM: Printed filament:90.75m Printing time:1 days …
-
I need assistance with auto leveling on a DELta printer. I believe i have followed your guides correctly, however i get illegal move errors when running G29. My Printer has an aluminum bed, and the sensor works, (it triggers at about .9mm o…
-
I need assistance with auto leveling on a DELta printer. I believe i have followed your guides correctly, however i get illegal move errors when running G29. My Printer has an aluminum bed, and the sensor works, (it triggers at about .9mm off of …
-
i have the exact same setuphere is my config.hi believe the full graphics controller encoder speed must be set to slowest speed to work correctly.dont enable sd support in the config tool. the display selection will support it, enabling both can cau…
-
Dec, the confusion comes from the conversion from cartesian to delta math and the axis names. I find it easiest to think of the towers as "A", "B" and "C". I wish that they had been named that way. It makes it easier to explain. "To move the x-axis,…
-
here is the rebuild 7:42:00 PM: Attempting to connect to printer 7:42:00 PM: Connection opened< 7:42:09 PM: ÿstart> 7:42:09 PM: N1 M110 *2> 7:42:09 PM: N2 M115 *4< 7:42:12 PM: Info:External Reset> 7:42:12 PM: N4 M111 S6 *67< 7:42…
-
i rebuilt the firmware and loaded it using 1/32 stepping and adjusted all the associated numbers, printer moving WAY slow now, but it still suffers from the same problems
-
i also have access to a4988 stepper drivers if thats the only solution, but i preferred the DRV8825 for heat, current etc.
-
all 3 jumpers are installed, this should enable 1/32 stepping, but i sent the command to make it 1/16.happy to use 1/32 if its practical with this hardware.Step size of stepper driver (A4988) jumper Yes/No stepsize ms1 ms2 …
-
my end stops are just mech switches, not opticals
-
sounds like a stepping/calibration problem try changing steps per mm?
-
its titled motor control in Rep 9.32. any assistance would be appreciated
-
ok i have rebuilt the firmware, but am having motor control problems. i opened a new discussion to try to keep the topics easy to reference for others.
-
also i found this code in a post and was wondering if this code was accessible somewhere to make things easier when changing micro stepping etc./** Drive settings for the Delta printers/ #if DRIVE_SYSTEM==3 // ***************************************…
-
MAX PRINTABLE HEIGHT 172MM (170 MEASURED TO GLASS BED IN HOLDERS +2MM) 12:16:01 PM: Attempting to connect to printer 12:16:01 PM: Connection opened< 12:16:10 PM: ÿstart> 12:16:10 PM: N1 M110 *2> 12:16:10 PM: N2 M115 *4< 12:16:13 PM: In…
-
ah. good to know. TYVM
-
sorry for typos.after i Open Repetier Host
-
i am trying to follow these steps, but afetr i open RefHost, i get a window with the variables, but no option to export.do you have screenshots? i am using a mac if it matters. also the current firmware is repetier.< 7:10:54 PM: FIRMWARE_NAME:Rep…