RonRock
About
- Username
- RonRock
- Joined
- Visits
- 5
- Last Active
- Roles
- Member
Comments
-
Well I did some more testing. I installed Repetier Host V2.1.6 on a different computer. Made 3 different Filament setting profiles in Slic3r. So those 3 and default gave me 4 different Filament (temp) settings. I also made proper changes in the Prin…
-
I uninstalled Repetier, found the folders in Windows Explorer that were left after the uninstall. Renamed them to old. Then reinstalled Repetier. On first opening of Repetier I got the Wizard so I followed through with it and left the temps at the d…
-
Very good. I will rename and see what happens. Seems like I will still have to reinstall Repetier to get the Slic3r back into Repetier. I will see.
-
I guess that I don't understand what you mean. Isn't what you suggest what I did? "I loaded a different STL into Repetier, made a change in my Slicer/Configuration/Print Settings, Saved then Sliced. Checked G Code and the temps are the same as…
-
I just went back to Repetier, loaded the same small STL as in the link above. Used Cura Slicer. I first went into Cura Slicer settings and set my temps. Saved Sliced. Checked my G Code in G Code editor. Do not see the expected temps again. Although …
-
Thank you. The first was just an example of what the issue is. It was a Benchy STL that I got off Thingaverse. I loaded a different STL into Repetier, made a change in my Slicer/Configuration/Print Settings, Saved then Sliced. Checked G Code and th…
-
Direct links [url=https://imgur.com/5xMtTPn][img]http://i.imgur.com/5xMtTPn.png[/img][/url] [url=https://imgur.com/O0Y2M6v][img]http://i.imgur.com/O0Y2M6v.png[/img][/url]
-
Thank You, I had given up on photo hosting sites since Photobucket went bad. Lost a lot of photos because of their rediculess cost structure change. Anyway here is a screenshot of the filament temps in Host/Slicer/Slic3r/filament Here is a …
-
Pretty sure I did as you say. I made temp changes to Slic3r/filament settings from the Configuration button in the Host Slicer tab. Then sliced with the profile just created ans saved. Open G Code editor to check and see incorrect temp settings. If …
-
Thank you, this issue has been fixed I think. Very confusing how to insert a thermister table into the configuration h file. At least for a newby with no knowledge of Arduino.
-
Very good now we are getting somewhere. I have found and looked at the online configuration tool Repetier has. Is there a way that I can download my current configuration from my printer as a backup in case I make a mistake with my soon to be create…
-
What leads you to think that I use Marlin? Isn't Marlin a firmware as Repetier is? If I am using Marlin I am unaware of it or how to use it. Perhaps that is my trouble, but I don't think that I am using Marlin. My third picture shows Repetier firmwa…
-
For some reason my temps did work for 1 print. Then I changed temps and they did not change for the print. Here are some screenshots, https://drive.google.com/file/d/1k8Bw4x4nZbsrIIQBloEaDoxk53tGDX_M/view?usp=sharing https://drive.google.com/file…
-
Thank you for the reply. The values I set as Max are 285C because that is the highest temp that is suggested by E3d-V6 hot end. I am trying to print with ABS and it's upper limit suggestion is 265, so I figured there is a little cushion. The bed tem…