mendelevium

I am appalled with the response I am getting in many forums about the mechaduino. I also sent a message to Jchurch but nobody bothers to answer. Is the mechaduino project dead? I stumbled upon it December 2019 and it immediately crossed my eye as…

in Squarish Circles Comment by mendelevium October 2020

Thanks. what type of LCD/touch screen displays exist which could be used over repetier/Ramps/Arduino? Price is not an issue. I came across BigTreeTech which I suspect can run with the setups I have but I have not been able to gather any informatio…

in DISPLAY SELECTION Comment by mendelevium August 2020

of course I am using repeter...yes I have ...ENDSTOP_Z_RETEST_REDUCTION_FACTOR 2 (can be changed to say 4, 5 etc)sorry I made a mistake.. Z steps per mm = 800Acceleration Print Z 200Move Z1300FeedZ Max feed 12Z Feed Homing 50 sorry for my mistake.M…

in Reduced feedrate on 2nd reference Pass. Comment by mendelevium August 2020

It does not seem to have any effect....these are my settings I have mechaduinos on X & Y. Z steps per mm = 800Z Feed Homing 50Z Max feed 12Acc 1300Z Print Speed 200 Do you suggest changing any of these? I think the 2nd homing process is importa…

in Reduced feedrate on 2nd reference Pass. Comment by mendelevium August 2020

Thanks will try out.

in Limit Switches and homing switches Comment by mendelevium August 2020

Thank You

in Firmware vs Eprom vs slicer settings Comment by mendelevium August 2020

Thanks!I am sure I compiled the correct version. I tried over and over and commanded M502 and M500 to flash and reload the eeproms...will retry...

in Selective eprom parameters Comment by mendelevium June 2019

Repetier, It does not work or I am doing something wrong.... I uncommented the homing feedrate and it still shows.I also have commanded M502 and M500 but they still appear This is how I modified the eeprom.cpp writeFloat(EPR_Z_MAX_FEEDRATE, Co…

in Selective eprom parameters Comment by mendelevium May 2019

thanks Mikelangelo noted

in DRIVERS AND STEPS Comment by mendelevium April 2019

Thanks for your lead.

in Homing problem Comment by mendelevium March 2019

After so much trials, managed to operate the ramps fan extender on one channel only.. #undef FAN_PIN #define FAN_PIN 11 #undef FAN2_PIN #define FAN2_PIN 6 With M106 S255, fan runs and M107 stopsI have swapped the Fan_PIn and Fan2_pin and noticed t…

in Part cooling fan Comment by mendelevium July 2018

thanks

in Skipping steps- New printer with Repertier firmware Comment by mendelevium July 2018

Hi Repetier, Thanks for your input, however I do not understand- your extender had pins 4 & 5..... what are you refering to?Did you alter anything in the Pins file? I am taking the 12 V input link from the ramps pins which power the fan. The…

in Part cooling fan Comment by mendelevium July 2018

I am sorry but I can`t fully understand. I need to only change the firmware file configration.h or need to change the Pins file as well? #define FAN_PIN 4 was -1trying to control Via pronterface now I can command M106 without getting unknown …

in Part cooling fan Comment by mendelevium July 2018

Sorted this but I cannot understand really how it came about. I used the online configuration tool which set my configuration.h file with the details under Heat configuration to read...#define HAVE_HEATED_BED 0changed this zero to 1 and it works f…

in HEATBED HEATER REMAINS ON Comment by mendelevium July 2018

Please can you let me know how to do this? is this a command through pronterface? I am not so smart yet in this Jargon. Thanks

in HEATBED HEATER REMAINS ON Comment by mendelevium July 2018

HI,Just changed the mossfet and it still does the same thing. As soon as I switch on, the heatbed would start heatiing...what are the pins you mentioned, so that I can have a look at this as well please?

in HEATBED HEATER REMAINS ON Comment by mendelevium July 2018

Many thanks Repetier. I succeed in achieving my requirement with the instruction you gave me. Many thanks again.