DBSDBS

Hello again. Because with 2.2.1 twice the entire system froses and ofcourse the prints failed, I would like to print WITHOUT a Repetier host... IS there a way to set this ofset for X in the printer? (I use CURA 4.9.0 for slising and then send the…

in Second extruder Comment by DBSDBS June 2021

Thank you very much!

in Second extruder Comment by DBSDBS May 2021

Here are: 1. The Log 2. Current Cura settings3. The detail (stl file) but with any file the problem is the same.4. The generated G-code LINK

in The first Z is "Layer high" + "First layer high" Comment by DBSDBS May 2016

This is the part from LOG concerning Cura engine: 16:45:24.573 : CuraEngine command:C:\Program Files\Repetier-Host\plugins\CuraEngine\CuraEngine.exe -p -v -c "C:\Users\Work\AppData\Local\RepetierHost\cura.ini" -s posx=0 -s posy=0 -o "C:\Users\Work\A…

in The first Z is "Layer high" + "First layer high" Comment by DBSDBS May 2016

Even after fully deleting of any ".ini" files in working dir, uninstalling, restart and reinstalling, when I use cure, the problem exists. When I use Slic3r, always the initial Z is correct.

in The first Z is "Layer high" + "First layer high" Comment by DBSDBS May 2016

I've deleted cura.ini from working directory, and when I've started again the Repetier, cura settings are still there.

in The first Z is "Layer high" + "First layer high" Comment by DBSDBS May 2016

Yes, It does not mater what kind of file I try. Every time the results are the same. I've tried even with the part that occurs automatically with new installation..

in The first Z is "Layer high" + "First layer high" Comment by DBSDBS May 2016

So, the problem is ONLY with Cura! With slic3r all is OK. I've uninstalled all versions of Repetier Host and Cura from the PC, have cleaned the registry, BUT when I've installed the fresh downloaded Repetier Host 1.6.1, all preview settings were in…

in The first Z is "Layer high" + "First layer high" Comment by DBSDBS May 2016

May be something by me is wrong.I've just installed Cura 15.04.5 and tried the same thingsEvery time when I try to change the first layer thickness, I receive "Layer high" + "First layer high" M190 S135.000000M109 S265.000000;Sliced at: Fri 27-05-20…

in The first Z is "Layer high" + "First layer high" Comment by DBSDBS May 2016

I'm a little bit confused.... 1. Thous settings are different from thous send by me...2. I use the bundled CuraEngine and do not know how to use Cura from command line...

in The first Z is "Layer high" + "First layer high" Comment by DBSDBS May 2016

Here is the content of the exported settings: [print]name = CuradefaultQuality = a78SGzXajD7MuKvFJzu1Iit9lhzQa7FAtravelSpeedMin = 60travelSpeedMax = 70firstLayerSpeedMin = 20firstLayerSpeedMax = 30infillSpeedMin = 40infillSpeedMax = 50infillType = …

in The first Z is "Layer high" + "First layer high" Comment by DBSDBS May 2016

Thank's a lot! Best Regards

in Unknown rows in Configuration.h Comment by DBSDBS August 2015

So, I'm not sure what for exactly is: #define ALLOW_QUADSTEPPING but when it is "0" all is OK. All the time the problem was in this parameter. It was "1" and I'm not sure why I had changed it. If @Repetier accepts ideas for improving the quality …

in Have had someone such a problem? Comment by DBSDBS August 2015

Is it possible this line to be a problem ones? #define ALLOW_QUADSTEPPING 1

in Have had someone such a problem? Comment by DBSDBS August 2015

Hi Repetier, After many tries and many spend hours, the final conclusion is that the problem is IN my Repetier's Firmware, because with Marlin 1.1, the printer prints vertically at all.BUT because I have other issues with Marlin, and in fact I like …

in Have had someone such a problem? Comment by DBSDBS August 2015

Thanks! Cheers

in G29 / G32 with Marlin 1.1 and Repetier Host Comment by DBSDBS August 2015

Unfortunately I didn't found the problem. The last that I can change is the firmware. But still do not decide which one to test.