raymond

Comments

• Thanks for your answer,is there any way I can try to move the other x axis via LCD?Or homing?Yes,I can only home one x axis.

  in dual x axis matter Comment by raymond October 2018
• Did you mean even it says Mirror motor signals to other stepper driver,but in fact it's independent Z axis but not a mirror?

  in Questions about dual X axis and Z2 end stop Comment by raymond January 2018
• I get a perfect result with dead time control now,Max PWM value 125,and Dead time lag 9. now it only swings 2 °C lower and 1 °C higher.

  in Extruder temperature not stable,changing in a range about 14 °C Comment by raymond January 2018
• i reduced max pwm to 115 and it's now only 1 °C higher then target temperature,but it's about 4 °C lower then the target temperature before it rises again,any advice for that?

  in Extruder temperature not stable,changing in a range about 14 °C Comment by raymond January 2018
• Thanks for the advice. I reduce the max pwm to 80,run M303 and the autotune finished . 00:35:32.802 : Info:PID Autotune start 00:37:29.424 : bias: 73 d: 73 min: 147.37 max: 157.95 00:37:59.859 : bias: 68 d: 68 min: 146.98 max: 153.69 00:38:29.…

  in Extruder temperature not stable,changing in a range about 14 °C Comment by raymond January 2018
• does the 0.91 have this matter?Change filament during printing is very useful feature.

  in Extruder motor never stop after pause and change filament Comment by raymond August 2017
• the version is 0.92.9 ,and I always make SD print.

  in Extruder motor never stop after pause and change filament Comment by raymond August 2017
• About this feature,my number is  Filament change x0[mm]Filament change y0[mm]Filament change z lift5[mm]Filament change first retract5[mm]Filament change last retract50[mm] all default numbers and when I changed filament right after started up the …

  in Extruder motor never stop after pause and change filament Comment by raymond August 2017
• Repetier said: Did you use G32 S2? If you used G29 that is not bed leveling just measuring average height at 3 points! GET IT，IT WORKS，THANKS

  in z-probing N*N grid measuring but only measure 3 points Comment by raymond December 2016
• Repetier said: For normal moves we have a lower limit from z max - you can only go down z length. Z probe is not tested for normal moves since probes do not trigger at z=0 they are normally ignored. When doing a probe move is the only ca…

  in do not stop when Z-probe triggered Comment by raymond December 2016
• Repetier said: There are z moves that do not test z probe. E.g. with delta it homes goes down and only then starts probing. A probe hit until that point does nothing. Could that be the case? Hi,I am newbie about the probe, I don't know how …

  in do not stop when Z-probe triggered Comment by raymond December 2016
• MartinH said: My probe is LJ12A3-4-Z/BX often open,  and connect the wire to the Z-min Pin directly, when triggered it manually, the   indicator  is on. These probes output 12 volts (if connected to 12 volt supply) if you have connected…

  in do not stop when Z-probe triggered Comment by raymond December 2016
• Repetier said: You might have set steps per mm in eeprom to nan or 0. That would cause such problems. Happens especially if you had 1 extruder config in the past. In that case also check the other eeprom values for extruder 1. Thanks!I o…

  in Dual extruder but only one move Comment by raymond November 2016