juulius
About
- Username
- juulius
- Joined
- Visits
- 234
- Last Active
- Roles
- Member
Comments
-
no rush, thanks for the reply
-
thanks for the quick answer
-
hi uhmm...... yeah, i guess doing late at night stuff is sometimes not a good thing. i releveled everything using G30 to get z heights. after that a g32 and saw that my height was off zo z-probe height wasn't good, after adjusting it everything…
-
How hot does your hotend go, also e3d hotends have 2 versions lite6 and v6. the lite6 can only handle temps up to 245 celcius with proper cooling, if you go higher than this you can melt the ptfe tube (bowden) the v6 uses a heatbrake, this seperates…
-
the pt100 board from E3D needs 5 volt to function, so the liniar graph from the board will be between the 0 - 5 volt. Radds boards can only read 0-3.3 volt,so the ADC wil be scaled between 0 - 3,3 volt, where the 8 bit controllers are scaling betw…
-
8-} so......... i found the problem.......... 8-} dumb me..... radds 1.5 has 4k7 resistors already on the board
-
owww think its a server issue, dont see those temps in the log
-
temps seem normal at {0,4000},{92,2400}, atleast what its showing now that room temp is 21 degrees, also when i see raw data at 110 its between {105,2320},{121,2240} im going to make a table of the datasheet, i still dont know what is happening he…
-
thanks 17:50:44.210: N26 m105 x017:50:44.217: ok 2617:50:44.221: T:24.58 /0 B:23.75 /0 RAW3:3921 B@:0 @:0 RAW0:391517:50:45.216: wait
-
dev version has the same problems a the 92.9 version i have this enabled in the config because of the diamond head setup Extruders share same heater from extruder 0 definition (SHARED_EXTRUDER_HEATER) and Mixing Extruder (1 Nozzle/heater + 2 or mo…
-
this is what i see 15:04:46.997: N1450 m105 x015:04:47.002: ok 145015:04:47.007: T:29.30 /0 B:-55.00 /0 RAW3:4095 B@:0 @:015:04:48.002: wait(bed thermistor is decoupled, no worries there) im running 92.9 shall try dev. but did some testing. i get cl…
-
oke did find the first problem m105 x0 only returns the raw value of the heated bed, not of the hotend. any idea?
-
the resistor is 4,7k, but what i find strange is that the sensor is reading normal at room temperature, but when hitting 90 degrees it stabelizes and wont go up further then 110 but shall heat up the hottend and meassure both resistance and raw dat…
-
is you z-height correct? if its to high it would crash into the bed. even if its correct try to lower it by lets say 20 to 30 mm. and then try to probe it (dont know if its a typing fault but the command is G32 S2). the G32 S2 will take care of z-he…
-
tried again but doesnt want to work, changed spi chan to 3 (as i guess thats the channel or mode) and after communication back to 0. the only thing i get is watchdog reset, no other communication. runned it with only the source code of the max3186…
-
solved the problem need to use programming port instead of native, now i can see it gets watchdog reset.
-
thought it would be a easy modification (not) but even with no sensor my due is just denying communication with the host, if i upload the firmware with 100k epos everything works fine dont know what is happening here i use the x_max endstop as s…
-
owh i think i found out what the problem is.. i need to set the max31865 to use spi mode 3 but everything else is using mode 0 as i can see in hall.ccp // Set SPI mode 0, clock, select not active after transfer, with delay between transfers SPI_…
-
also i saw that i posted this in the wrong category, can it be moved to the firmware side?
-
oke i tried and tried but cant get it to work, also i can connect to the due but no information is coming out of it (spi problem i think) this is the initialy code for the max31865 the first thing i saw was that it is somewhat the same to the max6…
-
i have tried it but with the probe (think it lies with my probe) i cant nail it quite (still getting around +-0.1) i had to set time and display settings on us otherwise the dot would not transfer to eeprom instead it would transfer big numbers.
-
hey guys just saw this thread was wondering if anyone had tried opendact
-
shall try it first with the max31855 setup because interface is the same, then i can see what for values i get and change the formule according to the readings from the e3d board
-
shall try. im going to upgrade from ramps to radds but have 2 pt100... the breakoutboards from e3d dont work with radds keep u updated
-
thanks... hopes it helps a bit with troubleshooting
-
so you have configured something like this?Z homing in negative direction direction (towards min endstop). (Z_HOME_DIR) i think that it has something to do with configuring the z probe also as z-endstop that it doesnt like here is my setup, i have…
-
oke sounds good. But what i meant was that i got middle in the print a debuglevel 14 now i dont know if after that there was a line "printer set in drymode" (but i guess there was)but it was continuing printing with cold nossle and bed. if somethin…
-
dont know what for printer you have but with the command G32 and G29 it wil go to the probing action. G32 homing + probing and G29 only probing. i use only G32 because i want to home first before probing. on my printer i have the following z-probe …
-
aha thanks
-
what i mean whith the QR code is dat now it wil direct you to www.mydomain.com:0 but the website my repetier server is running is www.mydomain.com i can use the QR code as it is, if i click somewhere on the page of the QR code website it wil redir…