Problem with Z axis

RAyWB · January 2019

so change

from

#define INVERT_Z_DIR 0

to

#define INVERT_Z_DIR 1

Dave_Da48 · January 2019

RAyWB said:

so change
from
#define INVERT_Z_DIR 0
to
#define INVERT_Z_DIR 1

I've tried, it don't work

RAyWB · January 2019

so moving direction should change when you change this parameter .

just recompile and upload

Dave_Da48 · January 2019

RAyWB said:

so change
from
#define INVERT_Z_DIR 0
to
#define INVERT_Z_DIR 1

Because wit invert all the z axis and It's worst

Dave_Da48 · January 2019

I've tried to changed too this

#define Z_HOME_DIR -1

but don't do anithing

RAyWB · January 2019

Dave_Da48 said:

I've tried to changed too this

#define Z_HOME_DIR -1

but don't do anithing

this just says the homing direction.

-1 is zmin,

1 is zmax

Dave_Da48 · January 2019

RAyWB said:

so moving direction should change when you change this parameter .
just recompile and upload

Escuse me but im not that stupid, my problem is strange

RAyWB · January 2019

Dave_Da48 said:

Escuse me but im not that stupid, my problem is strange

so good luck , just tried to help

Dave_Da48 · January 2019

RAyWB said:

Dave_Da48 said:

I've tried to changed too this

#define Z_HOME_DIR -1

but don't do anithing

this just says the homing direction.
-1 is zmin,
1 is zmax

And how i can change the homing direction? because the gereral direction o the Z axis still good, i ask go up, it go up, the problem is juste the homing dir ant the endstop

Dave_Da48 · January 2019

RAyWB said:

Dave_Da48 said:

Escuse me but im not that stupid, my problem is strange

so good luck , just tried to help

Yes and thanks you

RAyWB · January 2019

do you have a space between

#define Z_HOME_DIR and -1 ?

you previously posted

#define Z_HOME_DIR -1 (no space)

but it has to be

#define Z_HOME_DIR -1

Dave_Da48 · January 2019

RAyWB said:

do you have a space between

#define Z_HOME_DIR and -1 ?

you previously posted

#define Z_HOME_DIR -1 (no space)

but it has to be

#define Z_HOME_DIR -1

// ################# XYZ movements ###################

#define X_ENABLE_ON 0

#define Y_ENABLE_ON 0

#define Z_ENABLE_ON 0

#define DISABLE_X 0

#define DISABLE_Y 0

#define DISABLE_Z 0

#define DISABLE_E 0

#define INVERT_X_DIR 0

#define INVERT_X2_DIR 0

#define INVERT_Y_DIR 0

#define INVERT_Y2_DIR 0

#define INVERT_Z_DIR 0

#define INVERT_Z2_DIR 0

#define INVERT_Z3_DIR 0

#define INVERT_Z4_DIR 0

#define X_HOME_DIR -1

#define Y_HOME_DIR -1

#define Z_HOME_DIR -1

#define X_MAX_LENGTH 210

#define Y_MAX_LENGTH 210

#define Z_MAX_LENGTH 220

#define X_MIN_POS 10

#define Y_MIN_POS 10

#define Z_MIN_POS 0

#define PARK_POSITION_X 10

#define PARK_POSITION_Y 10

#define PARK_POSITION_Z_RAISE 10

#define DISTORTION_CORRECTION 0

#define DISTORTION_CORRECTION_POINTS 5

#define DISTORTION_LIMIT_TO 2

#define DISTORTION_CORRECTION_R 100

#define DISTORTION_PERMANENT 1

#define DISTORTION_UPDATE_FREQUENCY 15

#define DISTORTION_START_DEGRADE 0.5

#define DISTORTION_END_HEIGHT 1

#define DISTORTION_EXTRAPOLATE_CORNERS 0

#define DISTORTION_XMIN 5

#define DISTORTION_YMIN 5

#define DISTORTION_XMAX 210

#define DISTORTION_YMAX 210

Dave_Da48 · January 2019

Please help, I don't find anything

Roko · January 2019

Dave_Da48 said:

Please help, I don't find anything

I run the eeprom_clear sketch before I upload a new firmware so it will be fresh.
You stated things aren't changing. This may help.
In the Arduino program its under
File - Examples - EEPROM - eeprom_clear

MartinH · January 2019

sounds like the Z motor plugs need rotating 180 deg

Problem with Z axis

Comments