white_eagle
About
- Username
- white_eagle
- Joined
- Visits
- 114
- Last Active
- Roles
- Member
Comments
-
I am slowlu loosing my patience. Since the webcam is not functioning properly under windows and I wanted to run Repetier server in a Raspberry pi I installed Repetier server under Raspian.So far so good. Server installed and running fine. But now fo…
-
I also never said I was on Unix :-) Still problems though. The camera image is shown for a short while. After a minute or so the image freezes, disappears and the smal imag icon is shown. Switching to the image tab and then back to the video tab let…
-
Isn't mjpg_streamer meant for Unix? I followed your instructions in "Setting up a webcam in Repetier-Server for Windows" to set my webcam. Redid it again 3x this morning. Don't know what happened, but it works now.Some pictures to show my settings:
-
I post some pictures to clarify:
-
Can you please give me some tips how to get the graphical LCD working using hardware SPI?
-
I have entered the above value in the dynamic image url field.When going to video tab I now get a small image icon, but no video. When I open the url in a separate browser window the video shows ok.
-
My programming knowledge is unsufficient to be able to implement such code. I can give you the code that is used to test he display and buttons with the graphical LCD connected to the Ultratronics.Is it possible for you to implement his in your firm…
-
I can compile now. Must have done something wrong. One other question:I use the reprapworld graphical LCD on the Megatronics 3.0. To get this working I had to change the pin settings in ui.h for the Megatronics.I can not find info for the Ultratroni…
-
I downloaded the complete firmware here:https://www.repetier.com/firmware/dev/index.php and copied the HAL.cpp file. I will give it another try.
-
Downloaded the new HAL.cpp.I use the dev version. Still get an error, only different one: Arduino: 1.6.9 (Windows 10), Board: "Arduino Due (Programming Port)" sketch\HAL.cpp:2:24: fatal error: compat/twi.h: No such file or directory #include …
-
I finally have it working Using the configurator and your z-probe instructions I was able to set everything right an understand what happens. One final question: When I use G32 S2 autobedleveling results are stored in eeprom, right?Are they overwrit…
-
Yes, I use Repetier, Only got confused with Marlin setting. This is my Z_MAX_LENGTH value: 216.6 This value sets my bed under the extruder when I give G0 Z0. Doing some G30's at different bed positions gives:1.63 X45 Y001.28 X145 Y001.38 X145 Y150 T…
-
I am slowly beginning to understand it. I have my printer setup to home to Z-max, which is 216.4 mm under the nozzle.I have set the z home distance to 216.4When I type G0 Z0 the bed perfectly levels. I have enabled the Z- probe and when I go G29 it …
-
I am going to follow your recommendation of using the z-max endstop for homing. I need a little help with the setup.How do I tell the printer the distance from the probe to the bed after homing?I guess it is possible to lower the z-axis until it mea…
-
I will try that. And thank you for all your great help.I find it rather difficult to understand everything that is happen with the z-axis. I understand you recommendating for applying a z-max sensor with a z-probe, but in my case that is not very ef…
-
The problem only happened with Windows 10.Reverting back to windows 7 on my laptop solved the problem. So I guess windows 10 is not compatible with my laptop and it has nothing to do with repetier.
-
Stupid question, but where can I find the latest dev version?
-
I will try the dev version. Can you explain what you mean with the z-probe height of 0? When I home my printer, using the inductive sensor I have a gap between the bed and nozzle of 0.25 mm. After that I do a G29 to autolevel.In Repetier I set an of…