› ›

wabbitguy

About

Username
wabbitguy
Joined
Visits
21
Last Active
Roles
Member

Comments

  • I'm using the 3.8.0 RC2 firmware on my MK3S (was using the 3.7.2). They changed the PINDA probe for the MK3 and MK3S. It now includes a thermistor and there's a table in firmware they reference for the hot and cold temps. If printing inside an encl…
    in Files sliced in prusa slicer not working Comment by wabbitguy September 2019
  • Repetier said: Tried reboot to see if I can see something in log like dmesg on startup but did not see anything. Didn't even see your screen as shutdown was maybe too fast. Anyhow I have found this: https://medium.com/@sbyang/slow-shut-down-…
    in Slow Boot and Shutdown On Raspberry Pi3 Comment by wabbitguy August 2019
  • Repetier said: Strange. I did quite some testing and modifications to stop all threads much faster. In my tests I had no problems restarting quickly when server was idle. If some slow operation is in progress it might delay shutting down. Ca…
    in Slow Boot and Shutdown On Raspberry Pi3 Comment by wabbitguy August 2019
  • Installed the latest 0.92.1 ARMHF (via Repetier Server itself; no image used) and back to the 1:30 shutdown time again. The line showing is: Stopped Target NFS Client Services And we sit there for a minute and a half and then it continues to shut …
    in Slow Boot and Shutdown On Raspberry Pi3 Comment by wabbitguy August 2019
  • I have a PRUSA i3 MK3S and two delta printers. I use PRUSA slicer 2.0 and don't have any problems with the GCODE from PRUSA slicer and Repetier Server runs all three printers at the same time, all GCODE from PRUSA slicer. Repetier Server just sends…
    in Files sliced in prusa slicer not working Comment by wabbitguy August 2019
  • Isn't there a setting where you can save each printers configuration to your computer, then after the new install create the original printer just enough to get to the point here you can then upload the old configuration? If memory serves me right t…
    in Raspberry Pi 4 Compatibility? Comment by wabbitguy August 2019
  • That'll be great cause I san start from a known point instead blindly stumbling around in the dark...LOL Looking forward to the update! Thanks for the prompt response and a fabulous product! Mel
    in Raspberry Pi 4 Compatibility? Comment by wabbitguy July 2019
  • Did the rasp-config, needed to install lightdm, did that. Boots to a blank screen with the cursor top left corner...LOL Hows that go? I'm closer but no cigar...:-)
    in Raspberry Pi 4 Compatibility? Comment by wabbitguy July 2019
  • I managed to update the Raspberry PI for Buster and that went fine...Repetier Server starts up, connects and works fine. The only stumble is the Pi doesn't start Chromium to show the web GUI on the 3.5" TFT display, it just sits at the :$ line. No d…
    in Raspberry Pi 4 Compatibility? Comment by wabbitguy July 2019
  • Solved my slower start up and really slow shut down...I originally installed the server on my Rasp Pi 3 from the image download of 0.91.2 that was written to the microSD card (the armel version). As I noted previously, start up was slow but okay, b…
    in Slow Boot and Shutdown On Raspberry Pi3 Comment by wabbitguy May 2019
  • I just did a fresh install of Repetier Server and it boots up fairly quickly, shutdown, very slow. I can see all the stuff it's shutting down as it scrolls by in the TFT display but at the point where the Rasp Pi stops accessing the SD card and the …
    in Slow Boot and Shutdown On Raspberry Pi3 Comment by wabbitguy April 2019