shaiss
About
- Username
- shaiss
- Joined
- Visits
- 39
- Last Active
- Roles
- Member
Comments
-
Meh. That won't work as intended again. I'll never hear a tone that's running for 2 seconds. I'd really like to find a way around this as I'm usually in the house but not around the printer. So I wouldn't know it's out of filament till I check o…
-
@repetier maybe I'm doing something wrong. I added those HAL commands you mentioned above, but I think they're in the wrong place. When a "jam" event went off, the printer would reset. Does the below look close to correct?this is in printer.cpp s…
-
confirmed the without bootloader works as expected. thank you!
-
confirmed the "@pause ;comment here" works, but "@pause;comment here" does not get processed. so key is that space after the command before the ;. thx @repetier
-
This year? I can put my Pixle in dev mode and send you any crash logs or details you need. I may also be able to get other devices to verify. Let me know if i can help here
-
@Repetier thank you for the response! Might be worth adding this note to the end of the configurator tool. I've seen lots of confusion on this in various places.
-
Ah ok. So my mistake was forgetting the discs after the @pause. So @pause; should be: @pause ; And I could also do: @pause change filament ; pause and send msg. Thanks again and I'll unlikely this in the next print
-
Awesome, thx for the detailed response. I'll try this out over the next few days and report back.
-
As a note I have the same exact issue on my new Android 7.1 pixel xl. This worked fine on my old Android 6 moto. I'm running the latest server 0.80.3 pro. Hoping you find a solution soon as I'm really struggling with long prints and could use th…
-
Np. Good work and keep it up. I'll wait another day
-
I'll have to post my config as it's definitely hearable OK mine and it beeps for 60 seconds. So I hear it from other rooms in the house. I understand not including it, but would be great to have some documentation on manually adding it. Thank y…
-
I'm on the latest .80.2 and while the full ui works fine. The touch ui is blocked from other devices Repetier host private http://iob.imgur.com/uYGg/tHbEclH1Ny I understand is have to use a reverse proxy, but my understating from your comments abov…
-
@Repetier , has this fix been pushed into the latest dev? I did open an issue in the GitHub repo. https://github.com/repetier/Repetier-Firmware/issues/598
-
@Repetier great. Thank-you for the update!
-
Abby update on this @Repetier
-
@repetier, did you decide to add this option to the configuration? I'll post the details of my changes later, but it would be nice to have this configurable.
-
@Repetier, has this fixed been pushed into the latest dev?
-
Repetier said: Next release will allow access as long as no users are defined. Then it makes no sense as you can always do anything anyway. Only with users old restrictions will take effect again. @RepetierI'm on .80.2 and don't see this…
-
It's not bloated at all. You've done an excellent job. Every option there has its purpose.
-
awesome, worked perfect, thank you! It's simple enough for now, but maybe oneday, I'll have it do some melody :P Would be cool if this were added to the configurator tool for dev. since sometimes the printers in another room, you may not see that…
-
Awesome, thx will try that and post back
-
Would you mind sharing a sample syntax. It'll take me a while to figure the proper format. Pls and thank you!
-
yep that worked! for clarity. the replacement code is from line 320 in motion.h to 360:#if MULTI_ZENDSTOP_HOMING { if(Printer::isHoming()) { if(isZNegativeMove()) { if(Endstops::zMin()) P…
-
Yup. Will test and get back to you
-
Yes top is the min position. In this case moving in zmax is also prevented. Ill try the allways_check_endstops idea. But that would mean I could accidentally be at z min and further move z min and break my Endstops and smash the nozzle in…
-
Update 3. I tried setting back on home z to which works since the limit switches are no longer high. But that means the starting point height is now 2mm+first layer height. This option could work but I'd have to find a height that is far enough …
-
I get that but I'm trying to understand what happens if I don't enable that pullup
-
@paulnd, I was using a similar guess method to you. I think it needs to be more clearly defined or detailed in the FW or it's instructions. I had homing set to zmax, but for now gone back to manual leveling on my corexy as z is 400mm and it takes f…
-
G33 is in .92. I had it working yesterday. I'm going back to manual leveling for now as I just couldn't get enough accuracy for distortion correction to work properly. Will try it again soon. Need to focus on other parts of the build.
-
What would I use now in the .92 stable version if g33 is unavailable? Or do I have to go to dev?