joule5
Hello I've been trying for days to get my controller board to connect with host via raspberry pi gpio pin header. Do you know of any repetier specific things that need to be done for this? I always get the error no understandable response and I'm trying to use the AMA0 port.
About
- Username
- joule5
- Joined
- Visits
- 29
- Last Active
- Roles
- Member
Comments
-
If I change IO_ANALOG_INPUT(IOAnalogChamber, TEMP_2_PIN, 5) to IO_ANALOG_INPUT(IOAnalogChamber, TEMP_1_PIN, 5) Then the temperature reads correct but I was never able to get more than 3 temperatures to work. I need the heated bed to work now so if…
-
I managed to create 2 erroneous readings now. I'm so confused.
-
Screenshot of printer with nothing connected, chamber reporting temp. https://i.imgur.com/wuROsSi.png
-
I tried different pins and confirmed the pin definitions from the stm data sheet. Marlin uses PA1 for heated bed. Using PA1 didnt' help.
-
I have this in configuration.h #define NUM_FANS 1#define FAN_LIST \ { &Fan1PWM } #define NUM_HEATED_BEDS 1#define HEATED_BED_LIST \ { &HeatedBed1 } #define NUM_HEATED_CHAMBERS 1#define HEATED_CHAMBER_LIST \ { &HeatedChambers } #…
-
Trying dev2 with rumba32. M105 reports C: 59.4 even though its unplugged. I was able to make the fault occur for the bed but I cant seem to fix it. Isn't this right? // Rumba32.h Temperature Sensors#define TEMP_0_PIN static_cast(PC_4) // T0#def…
-
It works now after updating everything. I also had to change ZProbeServo to Servo1 in zprobe.cpp.
-
This doesn't seem to work. IO_OUTPUT(Servo1Pin, PA4)
-
This doesn't seem to work. IO_OUTPUT(Servo1Pin, PD15)
-
Issue still exists
-
Have you fixed your bltouch?
-
The meter showed changes on the other printer, ramps board. I didn't worry about what it was going to read because it is PWM. I only saw that it did change. That is not the case with anything ive tried on dev2. Maybe if i could compare more of the s…
-
Is your BLTouch set for 3.3v?
-
I'm at a loss here. Any more clues would be greatly appreciated.
-
I was checking manually on the delta sample. Also, I checked another printer's bltouch manually. That was a good explanation of why my meter returned those voltages on the other printer.
-
I just tried it with the deltatower sample and nothing happened.
-
I know that I can make my servo pin any unused pin. Im trying to use pin 4 like you did. I just cant get it to do anything no matter what I try. It stays 0 volts.
-
I realized that i have another servo defined but after deleting the extra one the problem remains. Is this correct for pin 4? #ifndef _VARIANT_ARDUINO_STM32_#define _VARIANT_ARDUINO_STM32_ #define PA0 0 //D0#define PA1 1 //D1#define PA2 2 //D2…
-
I need to try this still.
-
I think I'm stuck here on this issue. https://github.com/Aus3D/RUMBA32/issues/8
-
What am I doing wrong now that the bltouch wont deploy and I cant even find the signal for M340 P0 with my meter. Does it have something to do with PD15 being pin 63 in the firmware but the data sheet for stm32f4 says that is 62? Pointing to 62 didn…
-
OK I'm one step closer now.. I had #define ZPROBE_ADDRESS before IOEndstopZMin was defined.
-
/* This file is part of Repetier-Firmware. Repetier-Firmware is free software: you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software Foundation, either version 3 of …
-
I tried x8 steps, different drivers, and a bunch of different feedrates/accelerations. It wont stop skipping until the feedrate is
-
I put BLUETOOTH_SERIAL -1 and updated platform.io and the problem went away.
-
Ok i got a motor to move with _invert . I still have double letters. Some of the words are like this ssppeeeeeedd mmuulltippllyy (5). Im using a pi for the server but the double letter is the same on the pc connection.
-
I have an error in the file c cpp properties.json. it says, " cannot find c:... buildroot/boardfiles/rumba32/stm32f4xx/f446v(c-e)t. " where is this file?
-
I put the jumpers on for a4988 stepper drivers. I tried to enable 1 and or 0. I tried to disable eeprom and LCD. I tried different stepper driver and different stepper motor. I checked the main pwr voltage. I can't open eeprom but the info gets prin…
-
Where is it in dev2
-
These settings aren't in configuration.h