fanofcc

Comments

• You must mirror the 10 pin DIP to correct the pin.

  in LCD module to make it compatible with RAMPS1.4 board Comment by fanofcc December 2016
• I have G33 fail when leveling. Dont know why

  in z leveing bed failed Comment by fanofcc July 2016
• I thinks his mean PWM.

  in dac error Comment by fanofcc June 2016
• Tried but seem it's not stable. At least for me.

  in New way to auto-calibrate delta in one shot Comment by fanofcc June 2016
• Thansk you, Raywb. I'll try soon

  in A guide to add a simple menu? Comment by fanofcc June 2016
• So with 0.92.9, how to auto leveling in Delta?Thanks!

  in Kossel Type Delta Bed Leveling Problem Comment by fanofcc June 2016
• Thanks you. I'm looking for you

  in A guide to add a simple menu? Comment by fanofcc June 2016
• Really? I'm using homing to Zmax in my cartesian (RF 0.92.8) and seem very fine.Could you tell me why should not in latest release?

  in Proofread needed for G/M codes in reprap.org Comment by fanofcc May 2016
• I tried again but still hang on when click on Z-Probe on LCD menu. I use 128x64 Full Graphic Smart Controller.Here is my firmware: https://drive.google.com/open?id=0B3jY5m-ty2usX3JpS3dkZTlQVlU

  in A guide to add a simple menu? Comment by fanofcc May 2016
• Hello, RayWB. Can you show me again where to put the:case UI_ACTION_Z_PROBE:             if(!allowMoves) return UI_ACTION_Z_PROBE;             UI_STATUS_UPD_F(Com::translatedF(UI_TEXT_Z_PROBE_ID));             GCode::executeFString(PSTR("G29 S2\n"))…

  in A guide to add a simple menu? Comment by fanofcc May 2016
• I send G32 S2 fine from Repetier Host. I created a gcode file in SD card with G32 S2 only for leveling from my Machine.

  in A guide to add a simple menu? Comment by fanofcc May 2016
• Hello, RAyWB. Today i use repetier v0.92.9 with your modifications. The Z - Probing menu appear correct but when i use the menu, my Delta just go to Home and then restart.Do you have any ideal?Thanks!

  in A guide to add a simple menu? Comment by fanofcc May 2016
• @Repetier:Oh i did some tweak when probing and it work:- First, i reset all setting (factory eeprom)- Second, i set the bed coating value back to 0mm- Third, run G32 S2 (probe)- Fourth, set bed coating go to 4mmAnd then save all setting.It worked ve…

  in The Z-Probe ran fine but impact with my glass when print! Comment by fanofcc March 2016
• Thanks you!I just tried with a LCD controller and it worked like a charm. I'll test on my machine tomorrow! Thanks you, Ray!

  in A guide to add a simple menu? Comment by fanofcc March 2016
• Great! I'll try as soon as i can.Thanks you very very muech!

  in A guide to add a simple menu? Comment by fanofcc March 2016
• Oh thanks My probe mechanic is very simple:- The nozzle is connected with Probe pin (i use Zmin pin for probe).- The hotbed connected with the GND pin.- When the nozzle touch on the hotbed, they act like a simple mechanic switch (close the GND pin a…

  in The Z-Probe ran fine but impact with my glass when print! Comment by fanofcc March 2016
• Do you add the Z-prove gcode (G29) in Start g-code in your slicer?

  in z-probe and leveling Comment by fanofcc March 2016
• Great, it worked like a charm Anyway, how to add a command enu on the LCD? Could you help me more? Thanks!

  in The Z-Probe ran fine but impact with my glass when print! Comment by fanofcc March 2016
• Hmm i just tried to download Arduino 1.0. 5, remove the 1.6.5 form my PC and then install it. But the 1.0.5 version compiles Repetier 0.91 with error!

  in Repetier v.91 compatibility Comment by fanofcc March 2016