enrico77
About
- Username
- enrico77
- Joined
- Visits
- 5
- Last Active
- Roles
- Member
Comments
-
i think there's something wrong < 15:06:18: plane: a = 0.0004 b = 0.0007 c = 2.8911< 15:06:18: Transformation matrix: 1.000000 0.000000 -0.000383 -0.000000 1.000000 -0.000681 0.000383 0.000681 1.000000< 15:06:18: Printer height:158.65< …
-
when I launch this command the Z goes to -303.9 .... is it normal?
-
I set the homing on the end stop z max, but how do I now adjust the height to adjust the zero? do I use offsets?
-
if I had seen it before!
-
Solved! I write it if anyone had the same doubts. The resistors must be welded to any radds (they finally answered me by sparklab). for the display there is no problem, the 3.3 volt signals are compatible (read on the datasheet of the display) the …
-
however i am disappointed by the sparklab! the price is very high and in the end the product is lower than a Chinese! beyond that the display is just Chinese, but they will only do it and then ok ... but for the price you pay nothing really! the sit…
-
Ok, but i have due. for the display is not important because it is only output from radds, but for the encoder?
-
Ok, i have buy a Spark Lcd and adapter. do you know if the three smd resistors are to be welded to be used at 3.3 volts? of this lcd there is no documentation !!
-
Finally! Thank you very much for the support and for the time you dedicated me! Now everything works! Both the min and the max. if you want to do other tests i am available! But in the firmware where i find the version number?in which file? The pr…
-
So, have you found the bug? ????
-
Yes ! Arduino Due (original) and radds.
-
So, I did the test. if with the printer it stops in position x100y100 i do the command G01 Y10 F300 the endstop_miny works. from the same position I execute a G01 Y200 F300 l endstopmaxy works (I have reactivated in the parameters also the endstop m…
-
tonight I do a little 'tests just moving y, now I start to get confused ideas, after so many tests! better redo it !! if you have any test that you want me to let me know. the idea that I made myself reading the code is that something is wrong with …
-
I tried to load version 1.0.3dev; I tried to change eeprom set several times ... nothing.
-
Did you find anything wrong with the configuration? could it be an eeprom problem?
-
consider that I put myself in the same condition as yours ... so I disabled the endstop-max
-
for the output of M119 i have checked and the signals match
-
// ################# XYZ movements ################### #define X_ENABLE_ON 1#define Y_ENABLE_ON 1#define Z_ENABLE_ON 1#define DISABLE_X 0#define DISABLE_Y 0#define DISABLE_Z 0#define DISABLE_E 0#define INVERT_X_DIR 0#define INVERT_X2_DIR 0#define IN…
-
// ################ Endstop configuration ##################### #define MULTI_ZENDSTOP_HOMING 0#define ENDSTOP_PULLUP_X_MIN true#define ENDSTOP_X_MIN_INVERTING false#define MIN_HARDWARE_ENDSTOP_X true#define ENDSTOP_PULLUP_Y_MIN true#define ENDSTOP_…
-
This video is only for 3 min endstop ... but for max endstop is the same!!
-
Ok ... this is the link
-
ok, I think we can not understand each other! This evening (night) I will try to make a movie so that the problem is clear. I'll send you the link youtoube ok?
-
if Muhammad does not go to the mountain ... the mountain goes to Muhammad ????????????!! I put myself in your condition ... only three endstops ... xmin ymin and zmin ... I run homing ... everything is ok! with the axes at x150 and y150 I execute th…
-
I reversed the endstop y, as suggested. I clearly had to reinvent the y-engine direction (which was previously inverted). Now the situation is this: no engine with reversed direction, looking at the printer the home is on the left and near me. I do …
-
ok ... so ... talking in front of the printer: x axis runs parallel to me, left xmin and right xmax, y axis is perpendicular to me, more distant from me I have ymin and closer to me I have ymax, for the zeta axis I have a high zmin and a low zmax. T…
-
OK thanks. if you can serve I send you my configuration file. I configured with the online tool so I think I can exclude configuration errors. the only change made by hand is the line 416 of reperier.h #define start_step_whith_high 0.! everything el…
-
I'm using the latest version, the printer, under construction, is Cartesian. what do you mean when you write: 'cause the reads or the moves it self'? in the log file I copied here all those readings were real !! I was the one who crushed the endstop…
-
I can not load the image ... however, doing this last test I got distracted and the threaded rod that works as an adjustment for the endstop has literally entered the endstop breaking everything! start doubting the firmware repetier !!! I find it im…
-
this is the result in this test!
-
Ok, i have activated debug levek 64 ... i move with command G01 X50 Y50 F300 .... i push many times the y_max end stop and the y axis continued to move but ... ... ... in the log : < 13:00:25: start < 13:00:25: Info:PowerUp < 13:…