crocky
About
- Username
- crocky
- Joined
- Visits
- 135
- Last Active
- Roles
- Member
Comments
-
This should be dropbox link for the file https://dl.dropboxusercontent.com/u/30430570/climbing.log
-
They appear to be the problem areas in my printer logs. I do not get any error messages, just wait for a split second and then it continues on like nothing has happened but there is a blob where the tip has rested.
-
< 21:05:35: N94493 G1 X-4.03 Y21.18 E5.616> 21:05:35: ok 28954< 21:05:35: N94494 G1 X-4.15 Y21.24 E5.6215> 21:05:35: ok 28955> 21:05:35: T:227.78 B:89.87 B@:191 @:255> 21:05:35: wait> 21:05:35: wait< 21:05:35: N94495 G1 X-6.4…
-
Just found it looking for it now!
-
Thanks punkti, that looks pretty similar to what I am getting but I can't get the log files up for some reason. I have looked in the printer setup and I'm still not seeing it, I have General Extruder Printer Shape Webcam G-Codes but no log file. I …
-
I can't see an area to view the system logs, does it have to be turned on... The doc says it is under settings---->printer, but I am not seeing it?
-
I'm glad I wasn't seeing things. The firmware is the current raspian and it had update and upgrade applied to it just before the files were printed. I printed the files a second time just verify that I was seeing it, paused during the second print a…
-
Just noticed a couple of pauses part way through a couple of print files, the printer just sits quiet for a couple of seconds.... then continues on happily. The pausing does show as a blob because the tip is hot. This is on the Linux version registe…
-
Nice and easy to upgrade. Using chrome on the Mac and just press the upgrade button! When it finishes just load the page again and away she goes at 0.60.1
-
Got the make to work, small typo on my part Still not producing video yet.... I have a few things to check now.. 1 step at a time...
-
Hi Johan, Did you use the instructions for making mjpg-streamer as written here.. Mine gives me an error during the make! Can't remember the error message at present. I will try it again and see if it works. I am using a raspberry Pi 2, 32Gb, Pi c…
-
Worked for me too..... Thanks!
-
The webcam in the tablet is now working as well webcamXP 5
-
Had to put the rule in the Windows 8.1 firewall for port address 3344, works fine now I also registered it too, thanks for the help and pointing me to the firewall.... Cheers,Bob
-
I got the printer configured and presently printing a two and a half hour job. Still only working on it own local host so far. I'll check the firewall setting when it finishes the job... Getting somewhere now
-
Thanks.... I know see what I am printing
-
Here is the printer config file https://www.dropbox.com/s/146pbj7ayxu95tl/bandit.xml?dl=0 Repetier 0.91
-
Here is the butter fly gcode https://www.dropbox.com/s/5ivhazw21jo79hh/butterfly_repaired50.gcode?dl=0 The whole thing prints, just displays the top rh corner though.
-
Link to photo 1https://www.dropbox.com/s/jkoors80axubd4s/IMG_2067.jpgLink to photo 2 https://www.dropbox.com/s/58t6wgkurzaoare/IMG_2068.jpgLink to photo 3 https://www.dropbox.com/s/eptmly6j6fwbyqc/IMG_2066.jpg Think that will finally work?
-
Link to photo 1https://www.dropbox.com/s/jkoors80axubd4s/IMG_2067.jpg?dl=0Link to photo 2 https://www.dropbox.com/s/58t6wgkurzaoare/IMG_2068.jpg?dl=0Link to photo 3 https://www.dropbox.com/s/eptmly6j6fwbyqc/IMG_2066.jpg?dl=0
-
Link to photo1 Link to photo 2 Link to photo 3
-
There has to a switch somewhere for it.... I get in host for the Mac as well...
-
What sort of files? I'm using it with Kisslicer (reg) and Rostock Max V2 and I have had no problems with it. Bob
-
Okay... I'll wait..... Patience.....
-
How is the Mac version going now?, some of us really don't want to use the Windows or Linux versions!