ITGuruWoo
About
- Username
- ITGuruWoo
- Joined
- Visits
- 7
- Last Active
- Roles
- Member
Comments
-
Thanks
-
Will do. I will upgrade when a significant release comes out. Thanks for sorting as always
-
Just noticed that it works on one of my printers and not the other (the one that is running). Both accessing the same files (shared). Should both be the same config as both Prusas. Confused
-
Link to folder with one gcode file. I will also add a screen shot https://1drv.ms/u/s!Au5HIXj0KmuxiIpsjPZAzQimuYAO_g?e=6Bffsq
-
I will do tomorrow morning. Thanks
-
Thansk for the response. No Tasks seems to be running. The renders of the files is there just the 2d and 3d preview just show the bed etc with no models. Only errors are old but I guess could still be the cause so I have pasted them below Thanks […
-
I have the same issue but I only have a single pi, and everything is done on it. No 3d or 2d of items rendering for some reason
-
Thanks. I will restart when I can
-
Just upgraded to 1.4 new image. Only issue so far is that repetier server monitor thinks I don't have a license, yet the server is licensed and working
-
I am going to be away until middle of next week so may not get back with anything this week.
-
BTW the only difference to the old solution is the upgrade of repetier and changed pi (changed pi because it was happening on the original). Oh and latest Prusa firmware
-
Hi I have just moved the location of the pi, changed the usb hub (new hub) that the cameras are connected too. Running some prints now. If it happens again I will send the lsusb output. Fast reconnect is on but once the usb's go they are gone until…
-
Hi, So managed a couple of 7 hour prints or more on each. Pi has been up for 21 hours. Then a few minutes ago it disconnected both printers, pi and repetier still running. Printers connected direct to usb 2 ports on the pi 4. Same error as before. I…
-
Hi, Thanks for the response as always. By connected via a usb hub I meant the printers and cameras. I have now connected the two prusas to the two USB 2 ports directly on the pi, and left the cameras on the hub and have so far ran a couple of print…
-
thanks I will try again. It was running virtual as suggested with two virtual printers to simulate both jobs that were running. I have sent the server log via email. It shows wifi and missed pings but not sure if that due to the memory or the cause …
-
ok so this time it hit 75.7% memory. Still running, one printer has finished other is still going as long print. Not sure what you need me to send. debugger is still running 'c'. I can obviously send the gcode files. What else please and how to get …
-
FYI it hit 8.9% mem so i started the debug and hit c (hope thats what you need). Need to sleep now. Hope it gives us something. Looks like it will perhaps happen at the same point in the prints, but that a guess
-
thanks. I will start it as soon as I get home from work and hope it is ready to start debugging before bed
-
Sorry one last thing how do I add a virtual printer? Should I add 2 to replicate the issue using the same files etc? I can do this tonight and run it overnight, as It only ever happens some time into the print
-
Also yes us 91.2
-
Thanks. I will try this. Some more info in case it helps: repetier is normally using 9 to 13% CPU, 124 to 140M mem free (while printing these 2 models), always with 1 web connection open on my PC and the touch screen. It jumps to 15 or 16 cpu when I…
-
Thanks, already had it running and just saw this. It did do it overnight, top attached is the final frozen screen. Once the one printer gave up it looks like the other carried on (as it is still printing back at normal speed). It has an obvious mark…
-
Thanks. Network is normally solid (I have decent ubquiti wifi etc), I could use a wired connection as the pi is pretty close to a switch. I am running a display with the touch display as well. Hard to analyse where the issues is if I cannot get into…
-
Also ssh would not connect due to timeout.
-
Thanks for your help. All is working using the hub for everything now (just the way I wired it last time). Cameras at 640x480 and now no problems running 3 printers and 3 cameras. Thanks again
-
I was about to run it on my windows server until while configuring I realised I had all the hassle with the webcams . But it is there now if I decide to use it (with all the drivers etc). But Looks like it may be fixed on my pi . I think rather than…
-
So managed to get it to freeze. No messages worth mentioning at all. Going to try leaving cameras off for a while and see if I can still reproduce it
-
Thanks. I am printing at the moment so this will be a tomorrow evening investigation. I have left the long cables in and pulled the hub with the two printers on to use the prusa and all seems to be working ok. I am assuming its something to do with …
-
Hub psu is fine. PLease can someone give me an idea how to track this? Web side is still working but no comms to any of the printers, so no response etc. Thanks
-
Thanks