CBX_Micha
About
- Username
- CBX_Micha
- Joined
- Visits
- 15
- Last Active
- Roles
- Member
Comments
-
CBX_Micha said: Und, wenn ich das nicht falsch verstehe, sollte das OS die ermittelten Werte nach Kreuzchen-jagen auf dem Kalibrier-Schirm doch in die calibration.conf schreiben, oder nicht? Ich habe die Datei jetzt noch mal neu angelegt …
-
Jetzt wird es interessant:Als PI eingeloggt:pi@3D-Repetier-PI:~ $ xlibinput_calibrator --list ERROR: unknown parameter '--list' ... xlibinput_calibrator --list-devices show the devices availables Ok, dann also ...pi@3D-Repetier-PI:~ $ xlibinpu…
-
Danke für den Hinweis. Da muss ich mich mal durchfummeln...Bekomme ich nicht hin Auf dem Display kann ich zwar treffgenau die Kreuze antippen (mit einem Stift), aber in RS liegt das immer noch daneben resp. im oberen Bereich zu niedrig (ich muss …
-
So, kleine abschließende Info zu dem Problem:Dieser Fehler ist inzwischen nur einmal erneut aufgetreten. Zwischenzeitlich habe ich zudem eine zweite CAM dran (Logi c270) und bisher keine Probleme. Dieser Fehler gehört offensichtlich zur Gruppe der g…
-
Ja, ich werde berichten. Dauert aber. Haben heute sehr schweren letzten Weg mit unserem kleinen Hund zu bewältigen
-
... indirekt ... Er hängt mit einem kleinen Switch an einem FritzRepeater als Gateway. Das ist aber auch unauffällig. Hatte ich auch schon mehrfach neu gestartet (das ganze System), obwohl der am gleichen Switch hängende Rechner die volle Bandbreite…
-
Danke erstmal für den Tip. startAllCams hat allerdings keine Änderung bewirkt. Wenn ich mir die Tasks via htop anschaue, ist da nichts Auffälliges. CPU Durchschnitt liegt bei 0,28/0,37/0,31, Speicherlast bei rund 6% (390mb/8gb) und die einzigen Ta…
-
Repetier said: In which description do you mean? As I said we are not the authors of that plugin. Sure... But I hope the author read also here
-
... yepp, there my idea comes from. In Repetier former I have named it "GEEEE i3" so the connector make a "GEEEE_i3" from it.If this was the problem, you should include it in the description if necessary
-
So, let's move on... - CURA including all auxiliary folders (appdata & co.) deleted and remaining links with CC deleted - Reinstalled CURA (5.6.0), started, created printer "GEEEE_i3". - CURA ended, folder copied to the plugin directory, CURA s…
-
yepp, I have. With all kind of networks and around I'm familiar (... anyone know about ArcNet, Token Ring and other most Corvus based ones? ) At 1st I will try with a wired to prevent all possible faults that are possible at WLAN and then I see f…
-
japp... former with CURA and OCTO I haven't a problem (same PI, same room, same IP, ...) but I have to start on any topic... who knows?!
-
hmmmm... Why do I always have the ass card?! Ok, tomorrow I try to use a wired LAN cable. Have to take care of my wife before due a cable flying freely through the house has a very modest WAF ...
-
Repetier said: Haven't seen a Repetier-Server uploader in OrcaSlicer - where do I find it? In PrusaSlicer you can upload or print directly when you configure it. Apart from that all slicers work, just you need to manually upload gcode afte…
-
Or let me ask it another way: Which slicer works perfectly with Repetier on a Windows system? Cura is already clear that the plugin specified in the FAQ has not been further developed since Cura 5.0 and cannot be persuaded to cooperate in Cura 5.5.…
-
CBX_Micha said: Wenn ich jetzt noch irgendwie dahinter komme, wie man die Auflösung des Streams einstellt, wäre ich soweit erstmal durch, bis die fehlenden Teile für die Drucker eintreffen... ... habs gefunden ...
-
Ok, danke für die schnelle Hilfe, die ich noch mal wie folgt zusammenfasse: - Repetier greift sich automatisch den verfügbaren Treiber für die CAM- Der legacy- Treiber (enable raspicam | start_x=1) ist dem libcamera- Treiber (camera_auto_detect=1) v…