CBX_Micha
About
- Username
- CBX_Micha
- Joined
- Visits
- 11
- Last Active
- Roles
- Member
Comments
-
I access the MJPEG stream directly with VLC (IP?action=stream). The Raspberry is connected via LAN, the stream has PRIO 100 in the Raspberry Workstation router, the cabling is CAT7. So it's probably not the network's fault. I also operate 4 UHD sur…
-
Ahhh ok! I didn't think of that; sorry, my mistake...
-
CBX_Micha said: Neues Problem, was schon ein paar mal aufgetreten ist. Wenn es im laufenden Druck auftritt, ist der Druck tot. https://steamradio.de/3dp/Repetier%20Crash.jpg ... gerade wieder passiert und Druck versaut bei ca. 98% fer…
-
Neues Problem, was schon ein paar mal aufgetreten ist. Wenn es im laufenden Druck auftritt, ist der Druck tot. https://steamradio.de/3dp/Repetier%20Crash.jpg
-
... wegen falschen Zeilennummern oder ähnliches hat hier noch niemand gemeckert. Und ja: Ist ein 8bit Board. Ob das bei einem Reset die Verbindung trennt, weiß ich aber nicht. Wenn ich am Board selber einen Reset auslöse, bekommt RS das aber ausnahm…
-
Noch ein Update:Der Crash passiert gelegentlich immer noch. Es scheint mir, dass nach einem abgeschlossenen Druck RS einen Status nicht mitbekommt. Das lässt sich auch daran festmachen, dass (ganz selten) der Drucker beim Drucken einen Reset macht, …
-
I send it via the CURA plugin.Now I have saved the file local and take a look into: all ok. Also I have sent the file to RS via GUI (upload gCode) and it seems ok also (printing right now... file size is ok) That comes up only if I send it via the p…
-
Kurzes Update:Ohne M501 gibt es Ärger. Nach einem Neustart nicht, aber wenn man mehrere Teile in Folge druckt, werden diverse Zähler nicht auf 0 gesetzt und noch einige andere Merkwürdigkeiten. M501 sollte aber an erster Stelle im pre-Printcode steh…
-
Ok, mache ich mal. Mir war halt nicht klar, woher das kommt. Nach einem Neustart des RS-PI's ist das Problem jedes Mal weg, sodass ich erstmal RS in Verdacht hatte... Zwischenzeitlich habe ich M501 und M420 an die erste resp. zweite Zeile gesetzt. M…
-
Edit: I compared the log file with the log file that was created afterwards. Left side: log file with the head crash Right side: log file with the identical file (still saved in RS) from the same starting point. I don't really know anything about…
-
Ok... again right now...Here is the Video and both logfiles in a 7Z https://steamradio.de/3dp/240625-logfiles_videos_headcrash.7z (~30mb)
-
... I messed up the logging; my stupidity... But next time... And I home on X/Y/Z=0. It doesn't make sense with a touch sensor, at least with Z, otherwise. M501 is fine. That just tells the FW to reset all values to the default values currently …
-
Update:Just happened again! Same process; restarting RS fixes the problem... Now I need a new PEI-sheet, I think ...
-
No, it was before printing started while the start code was running. I hadn't changed the slicer start code; I'll attach it below and mark the spot where the head hit the bed with ***. The phenomenon always occurred after successful homing of the Z …
-
Ahhh ok. Then I have understood it wrong.Ty for the hint; found it...
-
Well, I thought otherwise... When a stream comes, you can read which X and Y values are passed through; At least I suspect so. You don't have to send the maximum to the CAM for the current layer. It would be enough if, for example, the maxima of lay…
-
Ok, I thought it wouldn't be that difficult to fill 4 variables with the min/max values per layer for the next layer and use it as a snap position. But as I said: I have no idea about programming. I just have my ideas sometimes...
-
CURA connect solved from behind through the eye
-
... Problem solved!It's a little crazy to solve but seems to work now... hell!
-
Sorry, but I have to come back with the problem... again I had a defective SSD and had to set everything up again. See also the thread https://forum.repetier.com/discussion/comment/46556#Comment_46556 The new SSD arrived today and everything is (…
-
... meanwhile, it seems to work. I'm just finished with the new SSD and now I'm perplexed that it was gone ?!? Time for the Ghostbusters... grrrr wlan0 is there now, just for fallback; it's connected via LAN. Why that isn't show here for eth0 is al…
-
... hmmm ... time to edit post gone... Log say this: [17.04.2024 13:54:23] : Execute error response:sudo: unable to resolve host SV-REPETIER-PI: Temporary failure in name resolution [17.04.2024 13:54:23] : While executing:/usr/bin/sudo /usr/local/…
-
Ok, next thing... I'm not able to set the WLAN country in RS. I have set it via console and raspy-config but it will be ignored. The red banner in /Global->Network/Time/ won't go and isn't also clickable to set the country from this point...
-
Ahhhh! Ok, now I get it. Thanx for the Explanation; then it makes sense BTW: I'm cloning the SSD to HDD right now. The SSD have more then 8 defective sectors and goes to silicon heaven not so far in the future. Can be that this was the initial f…
-
... just back with the Dog. Before, I have disabled the display autodetect and define it manually. That was the 1st strike. The 2nd one is that the handling of the serial ports are changed in bookworm so they don't see the touch. After changing some…
-
... takes longer ... I can't activate the touch screen anymore while using the same config.txt as before... Anything have changed... I start over
-
> In General->Manual Control... Ok, then I didn't really understand it. In the print area, RS had taken over the data that I had entered in General/Manual Control and of course complained.I have now corrected the print area and left the manual…
-
Since I had to reinstall and set up the system today, I came across a question that I had suppressed/forgotten the first time. This has probably already been discussed somewhere in a thread that I can't find... When setting up a printer (Marlin), RS…
-
CBX_Micha said: Unfortunately, I just have to straighten the PI's SSD first. I got the wrong plug and pulled out the SSD while running instead of the HUB... Can't boot anymore... Fu** Seems that I have to completely reinstall Repetier …
-
Yep, ty for the hint.None of the three HUBs want to work with the WebCAM. All HUBs are recognized by the system, such as a USB stick connected to the HUB for testing purposes, but the camera is not; at no one! That's weird! I'll try again later, con…