Aquilus
About
- Username
- Aquilus
- Joined
- Visits
- 4
- Last Active
- Roles
- Member
Comments
-
Thanks! I will check!
-
Yes, firmware 1.0.4 is great! I love it compared to the old custom version of SeeMeCNC, it gives me errors, info and it is intuitive through the builder to pull it up. Now since the other time you recommended it to me I will evaluate the dev of 1.0.…
-
I add the last reading of the plan with the eschel correction reaching a 0.06 plan correction. Despite all this, the print is not compliant on the first layer and at certain heights that seem to lead to the 80mm step of the motors the shifta print o…
-
Thanks for the answer, unfortunately despite a perfect three-point calibration with respective horizontal radius and eshel calibration I can't get a perfect or close plane. It is amazing how in the middle sector it is lower than the central sector a…
-
Perfect! I Will try today and i Hope for the reducing noise, thank you so much!
-
I can't find that string by looking in all the tabs, do I have to modify / insert it myself? i have only in configuration.h: // ################## EDIT THESE SETTINGS MANUALLY ################// Microstepping mode of your RAMBO board#define MICRO…
-
Absolutely yes! Regarding the motors, I don't know if I can ask here, having a 1.3L rambo I have to reduce the noise (which is high) and I must necessarily act on the firmware since it has digital potentiometers, I am identifying the string: #defin…
-
At the moment I have printed without autocalibration, only mechanically and it prints regularly. Only with an offset I have to figure out where it comes from. About the probe everything is ok, it was my oversight and it gives me relief as a thing.…
-
These are the coordinates he gave me with G33 L0: 13:31:44.060 : Info:Autoleveling enabled13:31:46.231 : G33 X-90.00 Y-90.00 Z0.00013:31:46.235 : G33 X-90.00 Y-45.00 Z0.00013:31:46.235 : G33 X-90.00 Y0.00 Z0.00013:31:46.239 : G33 X-90.00 Y45.00 Z0.…
-
The distance of the probe from the bed is 5mm, I noticed that with each different height (5mm, 10mm and 20mm) the probe changes result. The distance from the bed is 5mm and the activation of the probe is 3mm. Unfortunately regarding G33 S2 once it r…
-
I proceeded to recalibrate the printer again and the best result I got at the moment is this. For the 3d map I put an initial Z of 5mm starting from X0 Y0. Here it is. mechanical calibration and Eschel3D: Without G32 S2, only mechanical and Eshe…
-
Probably so you are right, now I check the firmware and correct and test immediately. Do you know what the #define on configuration.h is? Edit MIXING_EXTRUDER setting to 0, thanks so much!
-
I encountered an error, on the firmware EXT0_MIRROR_STEPPER set to 0 but once the machine extrudes it is on ext 0 and 1 both spin together. Why?
-
I managed to adjust the speeds by putting the standard ones, I had a moment of panic but now everything is ok. Regarding the calibration I proceeded to recalibrate mechanically and it has improved, now I will take back the tool you passed me and I w…
-
By mistake I reset the eeprom, why now the printer moves very slowly with the motors? EDIT It's ok, accelleration/print reset.
-
Yet after having mechanically calibrated XYZ perfectly, after G30, G32 and G33 I always have this result: https://imgur.com/Wbpntgi 15:22:30.804 : Info:Distortion correction matrix:15:22:30.809 : -14, 17, 19, 5, -4415:22:30.809 : -22, -2, -5, -40,…
-
Solved, I had to run G33 only after G32 right? Once done with G33 it crashed on Y, on the firmware I reduced: #define DISTORTION CORRECTION R from 100 to 90 and now it doesn't crash anymore. Should I also run S2 after G32 and G33?
-
Repetier said: G33 is independent from G32. You have a square defined in configuration.h for distortion correction. This must fit on your bed and be reachable with activated z probe offset. So it will only cover a part of the real bed. For de…
-
I am encountering an error, a strange problem with G33, practically after starting G1 X0 Y0 Z5 F5000 and starting G33 the probe reads only the first point and then stops giving error G33. The coordinates are as follows: 12:49:24.163 : N16 G33 L0*1…
-
Today I will finish configuring the rest, the last things like the leveling coordinates and the autotune pid. Having a firmware configured like this helps a lot to understand any problems and knowledge has increased, I hope they recap other opportun…
-
Resolved! Obviously my mistake but without my fault. In the firmware modified by SeeMeCNC the command for the hotend peek fan was M42 P6 S255, but correctly as it always had to be the right command is M106 P6. Same thing as the P8 with the differen…
-
Everything works and the printer would be operational if it were not for the fans that do not turn, the commands for the peek / hotend fan come in because as soon as I enter M42 P6 S255 the fan turns half a turn and stops, on the firmware I set EXTR…
-
Honestly I don't know, I proceed to do as you suggest of course, I am setting the digital pins on the fans and more but they still don't work, as the peek fan is pin 6 and I have always activated it with M42 P6 S255 but despite this it does not work…
-
ENDSTOP_Z_BACK_ON_HOME is set to 0 so it is not that, in the eeprom I have the Park position Z raise to 10mm but also setting it to 0 the carriage of the Z goes down anyway after homing
-
Solved everything was the fuse F3 of the rambo, this surprised me because it would mean that the Rambo 1.1B had the same problem, however now everything is ok and I am going to reassemble everything. Regarding the problem it is definitely the type o…
-
I fixed everything and it works fine now except that after homing the X and Y stay at the end of the stroke and Z regularly drops 5mm. Unfortunately I think I burned the power supply because the card does not turn on anymore, it happened after I sta…
-
I encountered an error when switching on, the machine starts as if it were in print with a request for pause, moreover the machine goes down once you click on confirm. Do I try to reverse the engines? Despite this, even when the end stop max sensors…
-
I love! An exceptional configurator! Very fast and advanced, I hope I have done everything right, 90% I copied from the old firmware 0.92.2 of the dual SeeMeCNC but more is new, I install it and update you thanks !!
-
Latest firmware? I try it ok, I see that there is the possibility to load the old configuration.h, but I have to avoid this if I don't want to run into the same problem. I'll update you soon, thanks!