› ›

3dnew

About

Username
3dnew
Joined
Visits
6
Last Active
Roles
Member

Comments

  • Trying again without SD and it works... I'll solve this problem later... I hope. I did a G32 S0 to have a new matrix with more points and them M500 to save in Eprom This is the result: 14:59:22.523 : N15 M322*2014:59:22.541 : Info:Autolevel matrix …
    in Z probe too high one side Comment by 3dnew June 2020
  • The biggest problem is that I'm not able to upload the new firmware because of Pibot board!! Impossible to flash the  firmware with the latest version of the IDE. Doesn't recognize the board. With the only one working version of the IDE (1.6.5) I ca…
    in Z probe too high one side Comment by 3dnew June 2020
  • Any help? Id like to use repetier :-)
    in Z probe too high one side Comment by 3dnew June 2020
  • Probably there is some bug in configurator online. I eliminated some code that I added in pause command on start on the online configurator and now the upload is ok. QUESTION 1 I sent G32 S0 and now I generated a mesh for the plane. At this point, …
    in Z probe too high one side Comment by 3dnew June 2020
  • Everything works with old firmware bit I still have this error when I try to install last version.
    in Z probe too high one side Comment by 3dnew June 2020
  • Thanks a lot Repetier. I configured the last version by online configurator but while I upload to the board, a the end of the process I have this message: avrdude: verification error, first mismatch at byte 0x0000         0xb8 != 0x0cavrdude: verif…
    in Z probe too high one side Comment by 3dnew June 2020
  • As in the title... after G32 S0 the nozzle goes down and scratch a little the plane and then goes to start printing on the left side. At this point, the extruder is 2mm higher than the plane but when it goes on the right side is very attached to the…
    in Z probe too high one side Comment by 3dnew May 2020
  • Solved this too :-) Probably is better if I wait before asking :-) I did it from configurator and works. Tonight I'll have some test on the correction bed level function.
    in Z probe too high one side Comment by 3dnew May 2020
  • Solved the problem of the status of the probe. It was a wrong assignation of the pin. The problem is: how to have a 9 points grid on the bed before to print? For example: 3 points on X with Y20  3 on X with  Y 40 3on X with Y 60 I configured the bil…
    in Z probe too high one side Comment by 3dnew May 2020
  • First of all thanks a lot! I inverted the motor on configurator and now is ok. Now I can move motor and I think I'll be able to test the printer. Let's start again with autolevel. I want to use a mesh of 9 points on the bed and I configured it in th…
    in Z probe too high one side Comment by 3dnew May 2020
  • Any help?
    in Z probe too high one side Comment by 3dnew May 2020
  • I used the configurator to set the new firmware. I solved some problems with Arduino Ide and now i flashed the firmware. When I start Repetier it operates only on extruder temp and fan. Motors don't work. End stop are H and probe is L. Tried to home…
    in Z probe too high one side Comment by 3dnew May 2020
  • I'm working with an old version of the firmware of 2016. Tried to configure again with repeater for Pibot configurator but nothing moves. Is there a possibility to configure a new firmware with mesh bed autolevel. I intend the bilinear one. Thanks a…
    in Z probe too high one side Comment by 3dnew May 2020