benecito
About
- Username
- benecito
- Joined
- Visits
- 11
- Last Active
- Roles
- Member
Comments
-
Wäre auch für mich eine spannende Funktion! Gerade was das Thema Printfarm angeht würde es einiges vereinfachen.
-
wonderful - works like a charm
-
thats not a problem at all But this way I can stop looking for a solution
-
I suppose my biggest mistake was trying to run it on the raspberry I got it working now. Thanks a lot.
-
first of all: the new interface for movements is great! I tried to work my way trough a custom ui today (I admit: a lot of trial and error) and everything looked great until I came back to check a few minutes back and saw this error message: Com…
-
Repetier said: Actually that is what Z_PROBE_WAIT_BEFORE_TEST is for. If set to 1 it waits with lowering until you hit the probe manually. Was added for e.g. cnc machines where this is required as well for tool changes. More important if you …
-
I use a switch for probing which I manually put underneath the nozzle when homing. This switch has a height of 16.95mm at the point it triggers. If I don't use the line like above the extruder moves down on the switch once, up to untrigger it and do…
-
now I ran into another thing I kind of forgot. I use a switch for Z homing underneath the nozzle, so I use the Z-probe settings. Before changing the homing settings it looked like this: #define Z_PROBE_FINISHED_SCRIPT "G1 X0 Y0 Z2 \n G4 P300 \n M2…
-
EXT0 had an offset of 0;0;0 EXT1 had one of -1219;0;0 after changing The offset for EXT1 to 0;0;0 everything works fine! I was not aware Extruder offsets influence on homing behavior. As EXT1 is just a virtual one for me in this printer for control…
-
I made a short Video. Maybe this helps understanding. I just tried switching off Z-Probing all together but it did not change anything about the strange x homing. Below the relevant parts of the config file #ifndef CONFIGURATION_H #define CONF…
-
Fair enough! Sounds like a good way to go for. Any estimate when the next version will be out?
-
Just tried some more: after homing X it goes back 15mm then homes Y, homes Z and tries to move too far to the right at the very end.
-
X and Y Homing direction is 1 X and Y motor are also inverted Endstops are configured correctly I just ran M114 and it returns: X:250.00 Y:205.00 Z:0.000 E0.0000 which correspond my axis maxima for X and Y What I noticed it behaves different when h…
-
I did manage to basically set it all up, but what I did not manage is the printer not driving into the switch. It moves the bed down, homes X, then Y, and then Z (at X=0 and Y=0) but after switching the button (twice) it goes down "into" the button…
-
damn, this is sad to hear... how can I change the temperature scale? That is for sure good enough to try it out.
-
Repetier said: So your button is higher then the bed? exactly! I just read through the Z-Probing "manual" and got the idea behind it. I assume it will take me some time to understand it in detail and get it to work, but I'll definitely t…
-
Instructions for using a JoyIt or Waveshare 3.5" Display on a RaspberryPi with the Repetier Server Image Thank you to RAyWB and codiac2600 for their Tutorial and their help 1. Copy the Repetier Server image to MicroSD using balenaEtcher (or any ot…
-
the files were all the same but I found the mistake without installing xserver-xorg-video-fbturbo it wont boot but installing it changes the fb1 to fb0 again i had to change it again or run the installations in another order Thank you both for you…
-
Step 1: Install latest RPi version of Repetier Server following normal directions Step 2: Edit config.txt file Edit Config.txt file on Boot Change LCD rotate to 0 lcd_rotate=0 Scroll to this section and make these changes, uncommen…
-
Wonderful! The Image works You followed the instructions described in the link above or did you do it differently?
-
this is the content of the file: GNU nano 2.7.4 File: /usr/share/X11/xorg.conf.d/99-fbturbo.conf # This is a minimal sample config file, which can be copied to # /etc/X11/xorg.conf in order to make the Xorg server pick up # …
-
thanks a lot - it did not work but displayd the following error: pi@Repetier-Server:~ $ startx xauth: file /home/pi/.Xauthority does not exist X.Org X Server 1.19.2 Release Date: 2017-03-02 X Protocol Version 11, Revision 0 Build Operating…
-
I just started over to find out when this comes up: it happens after I change Option "fbdev" "/dev/fb0" to Option "fbdev" "/dev/fb1" in /usr/share/X11/xorg.conf.d/99-fbturbo.conf After changing it back to "fb0" it boots again …
-
ok, that did work out so far! I followed the instructions of the pdf but now it's not booting any longer. It starts and shows me the terminal. Whats wrong now?
-
In the end I want to cool the whole build chamber using Peltier cells. But I need the air temperature to be fairly constant.