Mrshirtpocket
About
- Username
- Mrshirtpocket
- Joined
- Visits
- 7
- Last Active
- Roles
- Member
Comments
-
Thank you. Sure, I will send some over in the next couple days. It is quite the feat. ~Drew
-
I understand that the numbers may seem usual. The first two values you presented are correct but the third is not. I have the Z axis on a lead screw and for each layer I need to go up over a centimeter. But I still must retain the accuracy of the sl…
-
Ah I figured it out! max volume per second. Thanks for all your help so far. ~Drew
-
-
My settings are 60 and 60 for x and y. And 500 for Z. ~Drew
-
I appreciate the help. I have now fixed my steps per millimeter. However, my second problem still exists. The ratio between homing speed and printing/manual speed. Homing is perfect and printing is very slow. What could be causing this? I have check…
-
I had my steps per mm set to 200 but I have dropped it all the way down to 20. Now it at least prints inside the print area but not quite in the middle. When purchasing these motors, it said that this,1.8 deg. step angle(200 steps/rev.) Maybe t…
-
Hey Martin, I have checked the x and y max length settings. They are both correct. 1,965 mm by 2,250 mm. Any other ideas? ~Drew
-
I have resolved the issue. However, now that I have reset, after homing to start the print, when the print starts it will continue towards the structure but doesn't stop in the middle to start printing like it should. It just keeps going diagonally …
-
Thank you very much I appreciate the help. Must I go through the config. h file or can I use the Repetier config tool? ~Drew
-
Thank you very much! I highly appreciate it. I will look into Repetier Server for bigger slices. Are you telling me that Host could slow down after extended usage? And possibly start causing problems? Once again thank you. ~Drew
-
Thank you for the help. I do not have marlin, I have repetier firmware, and it happens frequently, how should I fix it?
-
Hey again, apologies for the late reply. Haven't had a chance to get online. I have made it further into my project thanks to everyone on the forum. I am making models, slicing them, then running them in repetier. However, I am getting errors. One e…
-
Mrshirtpocket said: Secondly, a couple more questions if Ray or anyone else would be willing to help me with, when uploading the config to the new board when I get to this point, do I upload all of repetier firmware onto the board or just the…
-
Secondly, a couple more questions if Ray or anyone else would be willing to help me with, when uploading the config to the new board when I get to this point, do I upload all of repetier firmware onto the board or just the config H file? The board a…
-
Sorry for the late response, where the machine I am working on is, there is little to no internet. I try to get back to internet as frequently as possible when I need help. Thank you Ray for working with me to get this figured out. In the past day, …
-
I have tried 1.8.5 though it still gives me the following error Expected primary expression before ';' token How can I go about fixing this? Thank you.
-
Okay thank you. I will do that. I have downloaded my sketch to be set up in a way that I think would make the machine happy once I set up the sensor to leave it in the air. But when I go to compile in arduino IDE it gives me errors. I have heard tha…
-
Hey Everyone, I have read through your comments an answers. They have been helpful and it has been very nice to know that I have support around me while I go through this. Here is the run down of my project. It can be a lot to wrap your head around.…
-
Thank you both for the suggestions and correct paths to follow, I appreciate it very much. I will follow the steps to the best of my abilities to get on the right path. Now, I should say that I have a home made machine, and it doesnt involve h…
-
Thank you both for your fast response time and helpful insight. I am totally okay with compiling a new config file and uploading it to my board. Though in the past I have "bricked" my previous boards by not uploading the second version correctly, so…