Filusico
Filusico
About
- Username
- Filusico
- Joined
- Visits
- 5
- Last Active
- Roles
- Member
Comments
-
hi also I don't have EEPROM active but I don't understand exactly where to insert the Pk Pd Pi valuesin configuration.h I can't find the above entries found with M303
-
personally I did as you say1- the laser function is activated in the firmware2 - from repetier host I set the command M452 to switch to the Laser function and with M450 I have the confirmation that I am in this mode.I connect laser power on the D10 …
-
quindi è del tutto normale che non l'avessi mai notato prima ma è qualcosa che è stato incluso nella nuova versione del firmware?
-
but if I am at the X100 Y50 coordinate and I want to tell the program that I am actually at X98 Y52 I cannot change the coordinates without moving the extruder.All CNC programs allow me to decide the value in which I find myself then if I come home …
-
I connected the laser on the D10 extruder pin of ramps 1.4 and the pin D9 of the fan on the TTL of the LASERwhy when I enable the D10 with the M104 command after 30 seconds does it give me the decoupling probe error of the extruder?
-
sorry I did not understand..you have the laser connected to the fan output to give it the 12V power supply.But the logic for enable/disable where pin you connected it ???
-
Is it only intended to use the extruder to be able to switch on the LASER?and the pins of the fan to regulate the power during work?
-
is there a code to turn the LASER on at minimum to see where it starts working and to position the material in the correct position?That is, if I put a wood and I have to make an incision in a specific point, I can't know exactly where the laser sta…
-
which host fan control software do you recommend for making grayscale drawings?
-
I have read many pages here but none that clearly explain what to do.Why don't you just tell me to edit with this text and which pin to use?you talk to me about not being able to use PWM and that from v2 it will be possible but when does V2 come out?
-
I'm sorrybut I don't understand what it means to assign the pin to the fan function?unfortunately I'm not a programmer and if you please explain to me what to change maybe I can do it.what should I change in the configuration.h file?
-
I tried to connect 12V on the D10 (extruder output) but starting the list it does not turn on.Do I have to manually turn on the extruder from the button?I downloaded the plug-in for inkscape but it doesn't create a Gcode for the fan ..?What do I con…
-
HelloI would need a hand if possible.I purchased a 5.5W laserand I wanted to connect it to the ramps - repetierbut I'm not a programmer and I don't know what to do.where I have to connect the 12V (PIN on the ramps) and the PWM signal on which pin.do…
-
HelloI would need a hand if possible.I purchased a 5.5W laserand I wanted to connect it to the ramps - repetierbut I'm not a programmer and I don't know what to do.where I have to connect the 12V (PIN on the ramps) and the PWM signal on which pin.do…
-
I'm sorry to say it but at me over 100 does not change the speed.it always remains max from 100 to 255if you check the software and if you can tell me what I have to change to have an excursion from 0 to 255
-
because from 100 to 255 it does not change speedmeasured with an optical speed reader ..is not that the new firmware 1.0.2 has something wrong?I use Ramps 1.4 and arduino mega
-
/* This file is part of Repetier-Firmware. Repetier-Firmware is free software: you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software Foundation, either version 3 of …
-
can you tell me what to change to avoid this problem:I make Z home and the extruder starts to go down to the bed (Cartesian printer with swhitch end of stroke at the bottom)the Z limit switch lights up and goes back for 2mmthen it goes down again fo…
-
NOI've always had it #define Z_PROBE_SWITCHING_DISTANCE at 0
-
I'm sorry to contradict you but this #define Z_PROBE_SWITCHING_DISTANCE 20 does not work ... I had to change #define ZHOME_HEAT_HEIGHT 20 bringing it #define ZHOME_HEAT_HEIGHT 5
-
yes but you did not give me an answer with here to change the height of the Z with respect to the bed during self-levelingcurrently giving the command G28 S1 moves me to the correct X Y coords (set for the 3 points) but the Z is raised by 20mm, with…
-
I installed the self-leveling system on my Cartesian printer using the universal kit with precision piezo-electric Z probe from www.precisionpiezo.it so the height of the probe is the same as the nozzle so what should I change to make sure that when…
-
found Thanknow runs the grid correctly.but after making the G32 if I print anything the extruder always starts at least 0.2mm lower than the value of the 1 layerWhat should I change to raise it ...?
-
I do not understand what you mean that P3 should be 20/100 I should set P3 to 0.2 but I do not understand where the three P1 P2 P3 values are in the firmware