spikey1973
About
- Username
- spikey1973
- Joined
- Visits
- 57
- Last Active
- Roles
- Member
Comments
-
thank you! very informative. last couple of questions.. 1): i know the bed to be slightly hollow.. in marlin there was a correction for that (hollowness specific, no bumps) is G32 enough to correct this or should i go for G33 with this? 2): to…
-
thank you for your response!! much appreciated, unfortunately it doesn't help me much. Probably because i was unclear. I'll try again and number my problems. 1) G32 vs G33 Oke so clearly my problem here starts with that i have no idea about the …
-
more or less a bump post.. but i would really like to know what the correct settings are in the firmware (and host) so i can store the transformation matrix in the eeprom. and how to make the matrix more precise if that would have any benefit...…
-
did G32 S2: the following are the results. 13:46:40.147 : plane: a = -0.0011 b = -0.0070 c = 25.474713:46:40.147 : Transformation matrix: 0.999999 0.000000 0.001085 -0.000008 0.999976 0.006971 -0.001085 -0.006971 0.99997513:46:40.147 : CurrentZ:2…
-
it was via host. wasn't much aware of the G32 option.. just looked it up and went and go and tried it.. seemed to work. just didn't do the s2 setup to save in eeprom (didn't set that up). also i will make try to make the grid a bit bigger. bu…
-
sorry i didn't explain that properly.. when i started at lower (say z=25, haven't tried z=10 yet today) i found that (with a (quick) 3x3 matrix) it does the following. 1) measurement at centre point (in stead of intended point 1/9). 2) measure …
-
@ repetier: am not sure what z10 and or g32 are but i'll figure that out. i indeed found the errors.. but when i started at a hight lower say a height @ 25 mm (Z25 ?) it had that end point error but i'll look into the z10 before i try something el…
-
Oke, it really seems like the bad contacts were really the main problem here.. so i did my basic calibration and i now started to do the bed height mapping. did it already once.. and i also tried with more measure points. (10x10) strangely enough …
-
oke thank you !
-
one odd thing though. I did a quick determination of the Z-length and set is as 180.68 in repetier-host : Home Z: 180.68 (is this correct? it was Max in the older version, seems like a risk for error when by accident different values are enter…
-
Oke this i should've been able to figure out myself. apparently the connections of the endstops wires that connect to the mainboard were not functional anymore, leaving a bad contact.. this is the last place where i'd expect problems from and this…
-
Anyway oke.. I'll try to start from the beginning then again. software: Repetier host - 2.01 Repetier firmware - 0.92.9 Firmware config files: https://www.dropbox.com/s/crky5jdcss880sk/Configuration-2017-05-28.h?dl=0 https://www.dropbox.com/s/vc…
-
the problem is that there are many problems and it seems nearly impossible for me to differentiate. I tried going for it problem specific but that led to no improvement. Thats why i'm asking for someone who works with the same printer and same so…
-
ps: geetech G2S with GT2560 mainboard i did find these links http://reprap.org/wiki/File:Delta_Rostock_mini_G2s_MOD_Repetier_0.91_Configuration.h https://www.thingiverse.com/thing:1301129 but it didn't help
-
oke.. Today i got the new endstop switches in and started on the rewiring. for this i twisted each of the switch wires (x,y,z pilar and the probe switch) i also braided the twisted x,y and z wires together as one bundle. i plan to guide them sepera…
-
oke.. the probing time really is not much of an issue for me.. i just want it to work. but personally i thought that "Z_PROBE_BED_DISTANCE" ([mm] = Max. distance to go back for next test) would make sure the spider wouldn't go all the way back up.…
-
indeed feel like starting at z=10 would be a good idea. unfortunately it doesn't solve the basic problem. i've made some screen shots and will post the links. but i also filmed the action of the printer and put it on youtube. both the printer as rep…
-
@ repetier: i tried this indeed, did make the slider not crashing in the fatal error at the end occurs just the same. hoe do i start the autolevelling / distortion map? @ roko: thank you, i set it to 60 and i'll just leave it so then. thanks for …
-
@ roko: i can move the arm till max 23 degree (0 degrees being flat) if i take the in account the 90mm radius. so this is definitely not flat, but maybe it is already to close. if i go for 0 degrees it really goes near the edge.. so like 105mm out.…
-
two additional questions: 1) Z_probe_bed_distance: [mm] = Max. distance to go back for next test. i really don't understand what is requested here... specially if you take in account also question 2: the max distance to go back is back al the …
-
@ ROKO and REPETIER: both thank you for the reply! it is still rather unclear how to measure it though. Repetier said: if you set printer radius right it will never go below horizontal. You should even never go near horizontal as that motor ha…
-
additions to the above. i've been trying again to find some solutions tonight.. ant haven't found much. but did find some extra info that sheads some light on issue nr 1: *) when selecting a different extruder (two extruders) the result is complete…
-
oke i'll try to describe it as simple as possible. i had a clean calibrated marlin system before i swapped to repetier. so measurements are known and should not differ. so i compare to marlin as that is my known. 1) homing: Marlin's behaviour / e…
-
i wasn't at all sure about the dpi of my monitors. just the settings in pixels. small monitor: 1366*768 pixels, 13.6"x 7,7" size = 100 dpi larger monitor: 1920*1200 pixels, 20.5" x 12,8" size = 94 dpi so both are rather on the edge, but nothing ne…
-
what do you exactly mean with normal dpi? when is it normal? and i understand i can't solve this issue.. but i was referring to the link of my other topic that is more emeregent to me and has no reply at all. was hoping you could have a look at it …
-
seems to me like this is a repetier specifiek forum and that your question is a much more general 3d printers replated. or even further... but seems like a plausible idea.. you just won't be likely to find an answer here. grtz Matthieu
-
seems like an aswered question.. i'm not going to interfere..
-
i'm just a newbee, and am not to familiar with the da vinci mini w series. but it seems pretty similar to a lot of other printers, so a rather standard design. i think the best bet is to start with the latest version and start the setup file. if yo…
-
oke, just let me know if you need any further info... an other question.. any idea how i can get some help on this topic? i really have no idea what the issue could be.. is also no idea where to start trying to solve it. https://forum.repetier.co…
-
this was the only that i noticed directly as it is functional, but since you asked i went through the entire program and looked specifically for layout problems. this is in no way a complaint..!! just me trying to answer your question to the full. …