N37
About
- Username
- N37
- Joined
- Visits
- 7
- Last Active
- Roles
- Member
Comments
-
But now it prints about 0,8 mm over the bed surface and proper homing level. So setting the 800 steps per mm changed height error about 10 times, so it is relevant to the 10 times less steps per mm comparing to the 8000 value it was before. I have…
-
#define ZAXIS_STEPS_PER_MM 8000 I think my BUG is here, shouldn't that be 800 for 8mm per rotation pitch with the rods that I have now ... ? It is so simple, that i feel so freaking stupid to bother you guys ..... Free beer in Cracov on Poland,…
-
I've got all stepper drivers set DRV8255 1/32 microsteps standard nema 17 200steps per rotation stepper mottors. 16 teeth pooley for GT2 belt driven x and yAnd rods are 8mm x8mm per rotation for Z i must admit that my prototype was using M5 standar…
-
#define DRIVE_SYSTEM 0#define XAXIS_STEPS_PER_MM 200#define YAXIS_STEPS_PER_MM 200#define ZAXIS_STEPS_PER_MM 8000#define EXTRUDER_FAN_COOL_TEMP 50#define PDM_FOR_EXTRUDER 0#define PDM_FOR_COOLER 0#define DECOUPLING_TEST_MAX_HOLD_VARIANCE 20#define …
-
p.p1 {margin: 0.0px 0.0px 0.0px 0.0px; font: 13.0px 'Helvetica Neue'} SENDING:G28 ok 0 X:0.00 Y:0.00 Z:0.000 E:0.0000 ok 0 ok 0 >>> M114SENDING:M114ok 0 p.p1 {margin: 0.0px 0.0px 0.0px 0.0px; font: 13.0px 'Hel…
-
Ok, Thank you for your answer. Right now i'm trying to figure out a most easy and on the other hand stable way of fixing the build plate to the 3 or 4 rods.It is not so simple as the every plate/rod mount point needs to have flexibility to give plan…
-
Hello, i have got one little question, I'm designing new printer frame, as a closed box, and i want to make it able to full hardware auto level.I'm going to use the tension-meters under the printing head , just like RF2000 uses. And to make it full…
-
Ok, that makes the things crystal clear. So last one fast question, what is the FAN1 and FAN2 PIN in default configuration of repetier assigned ? Exactly where on board i can find that FAN1 pin ? *assuming default configuration using webconfig) And …
-
Thanks, i'll look in to that next week, right now we have got more phisycal design stuff to handle.
-
hmmm, i didn't know that. So if I design the bed drive for Z axis that has 3 leedscrew pillars with 3 independent steppers for each pillar, and and CoreXY two steppers for X and Y axis . Than the printer will be totaly automatic in terms of autoleve…
-
" Also note that you can not explicitly control cooler can defined in extruder setup" That was my case. I assumed that setting the fan speed in % in menu wil override the automatization of fan.I thought that if I will set 25% manually in menu it wil…
-
hmmm, i didn't know that. So if I design the bed drive for Z axis that has 3 leedscrew pillars with 3 independent steppers for each pillar, and and CoreXY two steppers for X and Y axis . Than the printer will be totaly automatic in terms of autoleve…
-
Thanx Roko, that's a good idea. Roko said: @N37 - for what it.s worth, along with changing the EEPROM MODE in configuration_h, (it's line 427 for my configuration_h) before I flash the EEPROM i run the sketch under File-Examples-EEPROM call…
-
i have definied only one extruder (extruder 0) and i use D10 connector on RAMPS 1.4 as extruder heater, so it is default configuration for that setup. Heated bed uses D8 in my configuration so it is also default setup. So D9 connector is not used at…
-
Thanx, I like to know what code I use, as you can see i'm a kind of person that wants to help and put some effort and work in finding bugs/testing/getting solution for the problem and sharing. Many people just asks a question and waits for gold solu…
-
Hello, Printer works, X, Y, Z, works fine. Heated bed heats up to proper tempExtruder also. But i cannot get the extruder 0 fan to work. I have got 1 extruder heater and it is connected to D10 (works fine) one heatewd bed, connected to D8 (works fi…
-
I'm sorry for my frustration. I'm glad that LCD is working. I have traced the Z axis moving problems to the EEPROM. I was using EEPROM set1 and 2 , and those values are now messed up. Firmware has got by default values set in EEPROM, and is ignoring…
-
Ok, so I have made full configuration with same settings than before.I have configured everything I need right now, but i have made no changes in: Start screen delayUI_START_SCREEN_DELAY[milliseconds]Time between page switchesUI_PAGES_DURATION[milli…
-
Ok, so problem is solved a bit I think. I have downloaded firmware from configurator where i have just enabled the smart graphic controller.No other changes. And LCD works, and works fine over reboots.Works fine over power off and power on. So it mu…
-
I was trying to test as much scenarios as I can to hep You find the differences.
-
One more thing. When I do not unplug LCD connector from RAMPS and flash the Marlin firmware on the repetier when the problem is active the LCD has got same problem with marlin on board. Problem ends with power reboot, and is not comming back (stil…
-
I've tested range from 100 to 150 and only difference is that when I flashed the firmware at first time with 120 after reboot (reboot after flashing, not unpluging the powersource) LCD was fine, but it might be similar to usung STOP button. But noth…
-
The problem is important for me, because I do plan to start production of printers before end of this year. Right nowe we have already prototypes ready from lasercutting i'm putting them tougether from pieces and adjusting things before final produc…
-
Forget abot plugging and uplugging motors, as you see on photos, there are no connections to them on pictures and problem still presists. even on "naked" ramps , i have just connected thermistrors to see if LCD shows dynamic data in real time (tempe…
-
Ok, i know how to "controll" the issue. LCD works everything is fine. menu works, i can change language... (here i have found bug, bat that's not important now. when you change language the menu is changing to choosen language, but status info on …
-
One last suggestion, As you may see on photo of LCD https://drive.google.com/open?id=0B4X4QYpSs7s4WlhFZ0FDQkVvS28 Those artefacts on GUI are parts of bootlogo and texts with website url and name that should be shown on startup before actual GUI is s…
-
I've noticed that, that's why i'm so confused. I've been speaking about that problem with my programist, a guy is more .net / mobile than embaded, but he pointed me to not enough memory /processing power as the source of the problem. I can eliminate…
-
I've tested same scenario with marlin firmware, and there is no glitch with LCD, using RC7 and swapping pins and so on, eben on clean not shilded cables without carring about interference and other things you mensioned, on the same hardware without …
-
Ok, so i have shielded the connection cables from RAMPS to LCD with aluminium foil and than with capton tape. And problem was solved solved. LCD starded showing fine image. But than i wanted to test scenario with disconnecting connector of the stepp…
-
True, but wiring is fine as the board is sitting on desk aside of the prinet as for testing purposes. I've noticed that changing arduino board to second one , and connecting the "old" one makes the LCD working again. Today i've had all day working …