› ›

Tanuki44

About

Username
Tanuki44
Joined
Visits
67
Last Active
Roles
Member

Comments

  • I just looked at the syntax for this command that I did not understand ...Cool, here's another point resolved. I will just forget about the 'temporary' and store in the Eeprom.Thanks
    in Z Sensors Comment by Tanuki44 April 2019
  • This is unfortunately what I feared too, hence my question  But as I want to keep the initial value in Eeprom (corresponding to FFF mode) ... Thanks
    in Z Sensors Comment by Tanuki44 April 2019
  • Ok for G33 I usually use the machine with only the SD. I wish I could set these values ​​temporarily via the Gcode file generated by the post pro. I was thinking of implementing a custom M code to do it ... as such as :     case 210: // M210 H    …
    in Z Sensors Comment by Tanuki44 April 2019
  • I will not be able to report all the tests and all the errors that I had .... BedLeveling's tests were all bad ...  Not finding a solution, I executed M500 and I imported a backup of Eeprom, things worked out. Finally, I think that's what repaired…
    in Z Sensors Comment by Tanuki44 April 2019
  • Usually, I do not use any correction except Z_PROBE_Z_OFFSET and Z_PROBE_HEIGHT I'm looking at this more precisely as soon as I'm at home and I'll say
    in Z Sensors Comment by Tanuki44 April 2019
  • "it does not depend on homing direction.so may be you give the 3 different points a try , may be it helps isolate the error" Ok for z_max, I tested the 3 points as soon as I'm at home.
    in Z Sensors Comment by Tanuki44 April 2019
  • Even in cnc mode, after G30, the Z axis goes down to the sensor and goes back to Z100 Z: NAN, then impossible to move the Z axis, only G28 unblocks the axis.
    in Z Sensors Comment by Tanuki44 April 2019
  • Have you progressed to measure tools mentioned here: https://forum.repetier.com/discussion/2749/z-probe-for-different-heights#latest 
    in Z Sensors Comment by Tanuki44 April 2019
  • I looked the CNC mode, the values ​​are well indicated and correct after the G92 Z0.Good work  Here is the link for the Confiiguration.h file https://1drv.ms/u/s!AlGMbs83UEm4gYg4vznCabw2tAsXfA  The values ​​of EEprom are in the post above. If G30 …
    in Z Sensors Comment by Tanuki44 April 2019
  • In fact, I do not really use the FEATURE_AUTOLEVEL, it is activated but I probe only one point, I should rather put FEATURE_AUTOLEVEL = 0, but is this important? ... I will look more precisely (display-for-laser-cnc-mode) and I will post the configu…
    in Z Sensors Comment by Tanuki44 April 2019
  • I use the 'Firmware EEPROM Configuration' in the 'Config' Menu. I exported the content, see post from 5:15Pm ... I'm not see anormal anything... I use the 1.0.3 version. I have tested in FFF and CNC mode, it's same... NAN ... I think like you, the v…
    in Z Sensors Comment by Tanuki44 April 2019
  • For simple G30 :  17:33:00.187 : wait17:33:00.859 : T:15.80 /0 B:16.00 /0 B@:0 @:0 T0:15.80 /0 @0:0 T1:15.80 /0 @1:017:33:01.078 : N16 G30*4517:33:01.078 : ok 1617:33:01.968 : T:15.80 /0 B:16.00 /0 B@:0 @:0 T0:15.80 /0 @0:0 T1:15.80 /0 @1:017:33:03…
    in Z Sensors Comment by Tanuki44 April 2019
  • For G30 H20 R0 : 17:36:13.078 : T:16.00 /0 B:16.00 /0 B@:0 @:0 T0:16.00 /0 @0:0 T1:16.00 /0 @1:017:36:13.296 : wait17:36:13.718 : N21 G30 R0 H20*1 17:36:13.718 : ok 2117:36:14.203 : T:16.00 /0 B:16.00 /0 B@:0 @:0 T0:16.00 /0 @0:0 T1:15.80 /0 @1:017…
    in Z Sensors Comment by Tanuki44 April 2019
  • With the modification of the 2 lines, the operation of G92 seems correct  G21G28G1 F2400 Z100G92 Z0                             ; redefined Z0                  but display LCD = Z:100G1 F1000 Z-50                  ; the Z axis goes down 50mm   displ…
    in Z Sensors Comment by Tanuki44 April 2019
  • Ok no problem, I test this and return feedback
    in Z Sensors Comment by Tanuki44 April 2019
  • Yes, you're right, the display on the LCD should indicate 80 but after the G30, it says 0 ...the log after the G30:Z-probe : NAN X:0 Y:0 After the M114:  X:0 Y:0 Z:NAN E:0 So even though it's perfectly detecting the piece, Z does not seem to have me…
    in Z Sensors Comment by Tanuki44 April 2019
  • G21                  ; metric valuesG28                  ; homeG1 F2400 Z100  ; Z degagementG30 H20 R0      ; ProbingG1 F200 Z90 Hello,I must have a problem, but without knowing where ...In the example:G30 H(stock height) R0the probe comes to palpat…
    in Z Sensors Comment by Tanuki44 April 2019
  • Thank you for your replyI will do otherwise, (use a gate 'OR' or an inverter switch)
    in Z Sensors Comment by Tanuki44 April 2019
  • Ok, I use a mega2560 with 256Kb ram. I thinks that actuatly the sort is by date of creation, the last written on the SD is often at the bottom of the list.I'll wait for the V2.Thanks
    in Sorted files on SD Comment by Tanuki44 February 2019
  • With the help of your code, I simply modified the file 'Commands.cpp' In : void Commands::processGCode(GCode *com)         case 0: // G0                   {                       // select faster axis max feed rate for g0,other axis speed is limi…
    in G0 Feedrate Comment by Tanuki44 August 2017
  • I only add these two files in the firmware folder? Is it directly functional for PRINTER_MODE_CNC or does it need to implement case 0?      switch (com-> G) {          case 0: // G0 -> G1          case 1: // G1 Thank you for your help !
    in G0 Feedrate Comment by Tanuki44 August 2017
  • Ok, this is a little  inconvenience, some post processors do not add the feedrate to the G0 because it is considered that the speed is setting in the controller by a variable or the max value of the axis. Thanks.
    in G0 Feedrate Comment by Tanuki44 August 2017
  • Ok, I understood the problem of the servo I will change my gcode at startup to avoid jitter. Thank for the explanations
    in tilting with servo Comment by Tanuki44 March 2017
  • I reduced to 10 and for now, it's fine ^^ Thanks again
    in Steps lost Comment by Tanuki44 March 2017
  • Thank you for your help, I will try and I will tell you back.
    in Steps lost Comment by Tanuki44 March 2017
  • #define MAX_JERK 20 #define MAX_ZJERK 0.3
    in Steps lost Comment by Tanuki44 March 2017
  • You can find the uilang (french section) here : https://1drv.ms/u/s!AlGMbs83UEm49T7rA5NcHNk-DR7c
    in French translation completed Comment by Tanuki44 February 2017
  • It's perfect Good job :-bd
    in Problem with Simplify3D comments Comment by Tanuki44 February 2017
  • Thanks to you, I will test this weekend
    in Problem with Simplify3D comments Comment by Tanuki44 February 2017
  • That's what I do, it's not important, only for 2 months a year, and I can also ask Simplify3D to correct their log. This remark was to alert the users, I spent a little time before understanding why the gcode file was no longer running. I was just…
    in Problem with Simplify3D comments Comment by Tanuki44 February 2017