Tinchus2009

About

Username
Tinchus2009
Joined
Visits
50
Last Active
Roles
Member

Comments

  • That is ok???? But the how do I do teh calibration of the sensor/noozle distance? I need to home Z in order calibrate the offset, there is no way to make a Zhome in other part of the bed? And no... I will loose more than a couple mms, I will loose a…
  • Auch, this is more complicated than I expected jajajajaok, I figured it ou and now the probe is woring, at least as far as I can tell (I can retract the probe, extended, detect H and L states). I followed the video instruction of pidgean but I cant …
  • O partially solved it. For some reason my ramps board is not delivering 5V in the servo pin... I tried gettin 5V from the aux pins and now the 3d touch works, but still Im not bein able to complete the steps,I was able to measure the x/y offset, int…
  • Hi. Im trying to install a bltouch clone (3dtouch , is exactly the same) so I guessed this instructions shuld have worked for me. But Im havening something wrong and I cant find what it is. I have recompiled the eprom (configuration.h is atached) I …
  • ok... I think Im on track , tahns a lot for the help. last questions: you said I can configure the fade in the online configuration tool. But I have configured my repetier firmware manually, and I read that for the online configuration tool works, t…
  • Thanks so much for your answer. I made a little mistake: the probe I will try to use is a servo/switch based probe (https://www.thingiverse.com/thing:2890290), it works somehow like bltouch but has a servo. Any idea how to configure it in repetier? …
  • Just a uestion: why dead time has been abandoned? so far worked really really well for hight temperatures, at least that was what I observed: for high temperatures worked much better than PID. PID worked much better for lower temps like 210 and lowe…
  • ok, great. another question: can the manual tuning of PID values be entered WHILE running a test print so I cant tune the parameter with the hotend doing real" print (tune parameters while hotend is moveing and extrudeing)?
  • Check what?  My config is a copy of my 0.92 version.... zjerk is set in configuration.h to 0.3 (default)... this message appears every time the printer is turned on
  • I see this too. But I homed the Z... lcd shows 0, but then when steppers are deactivated the ??? returns changeing from ??? to 0.00 this is normal?
  • By the way, Im useing version 0.92
  • doing the calibration pattern, Im useing a value of L+40 . In the pattern it looks god. The inserting the command M233 Y40 into my gcode of a print I see 2 things: 1.- corner of the brim is FAT, way way much than before and then the lines are heavil…
  • And what values you recomend for acceleration. I have 700 and Im going to check but I think I have tried with 400 too,
  • We only have to tune the L parameter we dont touch the K? Also, I use slic3r: I have retraction turn off, also no retraction in formware. Im printing a hollow cube to test how the corners comes. I have tried L 40,50 and 60 I dont see improvements (w…
  • Ok, really cant remember changeing none of these values or where to find them. Only one I chage was the Z steps, I did it through repetier host. How can I get back to a more fine z-babysteps controll? like only incrementing 0.1 at a time?
  • Well, thanks to you I somehow solved it, but if it is posible please help me a little ore to understand: 1- I already was doing the changes through repetier host. But it didnt worked. I tried a value of 5 for max z feed rate (that was the value mos…
  • Imagine you have a bed of 22X22 cms, and you want to take full advantage of it, you want to use hole bed. But in the corners of the bed you have a screw. If you configure the bed shape to have 22X22 cms, at the moment of usueing a G28 command, the n…
  • That DEV version is posible to be used or we wait till new release?
  • Actual speed of Z axis is 5. I tried: speed 4, this speed increase a very ugly noise comeing from the motors. Speed 3: both motor jam. Speed 2 works very nive, but it is slow?
  • Ok... I trid that: actual value is 5. If I set it to 4 is still quick.. if set to 3, both motors jam... 2 works ok but it somehow slow... Any suggestion? something related to the pololu/power? why the step motors jam at speed 3 but they work at spee…
  • Hi again, sorry to bother you On of the modification I did with this problem was increaseing the power in the pololu  of the Z axis. This didnt solve the issue. Then I solved it thanks to you, but today I realiced that I forgot to go back with the…
  • Great. My settings now are: STEPPER_HIGH_DELAY 1 DOUBLE_STEP_DELAY 2 Allow_quadstepping 1 The strange noise is not there anymore, and the homeing of Z works ok, no motors blocked You said "if quadstepping 1   may be you have to increase to DOUBLE…
  • Oh man... !!!! you are the man!!! ALLOW_QUADSTEPPING was already set to 0, so no change there I set STEPPER_HIGH_DELAY 2 DOUBLE_STEP_DELAY 3 Update: STEPPER_HIGH_DELAY 1 DOUBLE_STEP_DELAY 2 also works Can I also activate quad stepping? Update2 …
  • Ok. I will try but first, can you tell me how to know if I have those drivers? ince these setting seem to mess with internal of electronics I would like not to screw  thing up. Ipdate: looking at the pictures I found in google, my drivers are not 8…
  • Sorry, yes, 502 loads defaults from epron and then you save them with 500. I did that, and then I verified to be sure wich values were being used. I checked that. Here is more info: I separated X motors from the X axis, to check very carefully if th…
  • loaded configuration.h and then issue and M500 command
  • Ok.. those settings should not affect movements that much, but anyway I gave them a try: I changed each one of them like your configuration, but still failed. Will I have t go back to MArlin ?
  • Ok, I have tested this: - Increasing Z homing speed : fails too, in fact, the homeing speed in marlin is way faster of what I have tried with repetier - Loosing steps: I have seen motors loosing steps, but this is different, the motor gets stucked -…
  • Hi. Nothing helpful on the logs. I dont have LCD card. There are 2 slots were I can plug the sd module, I have tried and plugin into the other slot causes the printer not to start properly. I have run an M20 command: I get OK. M21 gives me "begin fi…
  • Not very helpful, do you sell the book "Firmware for Dummies"? Used the firmware configuration tool on the Repetier website and tried every different variation of SD Card reader until one worked for me. Simples! HI tooluser. can you tell me wich co…