PixelPusher
About
- Username
- PixelPusher
- Joined
- Visits
- 73
- Last Active
- Roles
- Member
Comments
-
Thanks Roko
-
i hope that's not it, but i was able to get a skirt but only at the cost of not having a brim or raft. that sucks.
-
Yes. In RH, I go into Config... under "Skirt and Brim" I adjust my settings as normal. But, under "Adhesion Type" there are only three options: None, Brim, and Raft. Since I normally use a brim, that kinda sorta works as a skirt, but it can get …
-
Thank you for your help, i really do appreciate it.with your instruction and some trial-and-error i got x and y moving in correct direction! thanks again,Richi
-
I reversed motor connector 180, it does move in correct direction... but now my X endstop does not work. Moreover: when I move carriage towards my endstop (to the right) and depress endstop with my finger, it does not work. However, if I move to -X …
-
I still cannot get my X and Y moving in the correct direction. The config below is what I'm using now, I know it's wrong (backwards) but at least it's working and I'm able to get some really cool prints going! Unfortunately, I have to reverse my obj…
-
I'm sorry for the confusion. I did not change the firmware... actually, I couldn't find any settings to change while looking for Extruder temp settings. Ah crap!!! lol... I just did a 'line-by-line' search and found "MAXTEMP 180" under the 'Heat…
-
Thank you.That "sweet spot" advice helped. Also wiped a tiny bit of my wifes hairspray and that worked pretty good. Although, I still was not able to increase extruder temp above 180. In settings I have temp set to 190, max at 200. Still cannot manu…
-
Ah! EEPROM. I don't know what eeprom is for, so I disabled it. THAT was my problem. I was changing settings to firmware but eeprom was taking precedence. This is probably why I could never get my x and y axis and endstops to behave correctly. I will…
-
sorry, I understand now what you mean about make the pin x max endstop (thought you were talking about altering code). I switched the endstop on the board from Min to Max but now my endstops don't work at all. Getting close, just trying to figure ou…
-
thank you for helping me get my head around this. I know the logic is simple, I just can't figure this out yet. I've tried several combinations of (0,1,and -1). I was actually able to get 'home' and even send a print (although i still need to fix Z-…
-
I'm using 1.6.5 Yes, manually I can move each axis individually. G28 X0: Nozzle moves Left (away from my endstop) and I must emergency stop.G28 Y0: Bed moves towards me (away from my endstop) and I must emergency stop. All three endstops are plugged…
-
I replaced my Mega2560 and everything is back to "normal." xyz manual movements seem normal. M119 produces this: I entered G28 and Nozzle moved down very slowly until endstop, then Nozzle moved in X and Y at same time (my DRIVE_SYSTEM is, in fact, s…
-
It's set to 0. woke up this morning and now my computer won't even recognize it (i did not touch firmware or anything else). All my problems could be because I bought a cheap kit from Replekio...cheap electronics from China. Replekio won't answer my…
-
ok, reset #define X and Y home. uploaded firmware and restarted RH. Entered G28 and Z axis moved down very slowly until Endstop (so far so good), then the X and Y motors ran simultaneously until the Extruder stopped at the front right corner of my b…
-
Thank you VERY much Couri!I'll give it a shot.
-
here is a screenshot of my printer settings.
-
I guess G28 is 'home' or 'set home' something like that? When I entered g28 Extruder moved Down on Z until hitting endstop... good. Then it moved Left on X but since there's no endstop on left side, it kept running and had to hit Stop again. My 3% u…
-
Thanks for replying...If I hit the "Home" button the extruder will move all the way to the left (x-axis) until it physically can't go any further (runs into x-carriage rod), and the motor keeps running/grinding and i have to hit Emergency Stop butto…