› ›

SimonTerhorst

Hallo, Ich habe progleme mit meinem Server die ich nicht genau eroeieren kann. die letzten 5 Drucke kam die Meldung : Error:Thermal Runaway, system stopped! Heater_ID: 0 Danach muss ich immer einen Kompletten Stop ausführen. Vorher macht der Drucker nichts mehr. Ich kann mir nicht erklären wie das Passieren kann. Bitte um Hilfe Letzten Zeilen von Druck Report: Send:9:16:07.290: N5407 G1 X59.718 Y113.429 E-.04129 ; wipe and retract Recv:9:16:07.298: ok (N5407) Send:9:16:07.298: N5408 G1 X59.593 Y113.492 E-.04156 ; wipe and retract Recv:9:16:07.315: ok (N5408) Send:9:16:07.315: N5409 G1 X59.147 Y114.048 E-.21161 ; wipe and retract Recv:9:16:07.322: Error:Thermal Runaway, system stopped! Heater_ID: 0 Mesg:9:16:09.425: Firmware stopped! You can only send host and shell commands until you hit emergency stop or restart the printer. Eventually running print is stopped. Mesg:9:16:09.652: Error:Printer halted. kill() called! Recv:9:16:09.652: TFT Serial Debug: Kill command... J11 Mesg:9:16:09.652: Firmware stopped! You can only send host and shell commands until you hit emergency stop or restart the printer. Eventually running print is stopped. Mesg:9:16:09.652: //action:poweroff Mesg:9:16:14.316: Warning: Communication timeout - resetting communication buffer. Mesg:9:16:14.316: This means that a expected firmware response was not seen within the expected time. Mesg:9:16:14.316: The typical reason is a communication error and print should continue after the communication reset. Mesg:9:16:14.316: Connection status: Buffered:39, Manual Commands: 2, Job Commands: 6 Mesg:9:16:14.316: Buffer used:39 Enforced free byte:0 lines stored:1 Mesg:9:16:14.316: Firmware stopped! You can only send host and shell commands until you hit emergency stop or restart the printer. Mesg:9:16:14.316: Firmware stopped! You can only send host and shell commands until you hit emergency stop or restart the printer. Mesg:9:16:14.316: Firmware stopped! You can only send host and shell commands until you hit emergency stop or restart the printer. Mesg:9:16:14.316: Firmware stopped! You can only send host and shell commands until you hit emergency stop or restart the printer. Mesg:9:16:14.316: Firmware stopped! You can only send host and shell commands until you hit emergency stop or restart the printer. Mesg:9:16:14.316: Firmware stopped! You can only send host and shell commands until you hit emergency stop or restart the printer. Mesg:9:16:14.317: Firmware stopped! You can only send host and shell commands until you hit emergency stop or restart the printer. Exec:9:16:14.317: @stopLog

About

Username
SimonTerhorst
Joined
Visits
1
Last Active
Roles
Member

Activity

  • SimonTerhorst
    Hallo,

    Ich habe progleme mit meinem Server die ich nicht genau eroeieren kann.
    die letzten 5 Drucke kam die Meldung : Error:Thermal Runaway, system stopped! Heater_ID: 0

    Danach muss ich immer einen Kompletten Stop ausführen. Vorher macht der Drucker nichts mehr.

    Ich kann mir nicht erklären wie das Passieren kann.
    Bitte um Hilfe

    Letzten Zeilen von Druck Report:
    Send:9:16:07.290: N5407 G1 X59.718 Y113.429 E-.04129 ; wipe and retract
    Recv:9:16:07.298: ok (N5407)
    Send:9:16:07.298: N5408 G1 X59.593 Y113.492 E-.04156 ; wipe and retract
    Recv:9:16:07.315: ok (N5408)
    Send:9:16:07.315: N5409 G1 X59.147 Y114.048 E-.21161 ; wipe and retract
    Recv:9:16:07.322: Error:Thermal Runaway, system stopped! Heater_ID: 0
    Mesg:9:16:09.425: Firmware stopped! You can only send host and shell commands until you hit emergency stop or restart the printer. Eventually running print is stopped.
    Mesg:9:16:09.652: Error:Printer halted. kill() called!
    Recv:9:16:09.652: TFT Serial Debug: Kill command... J11
    Mesg:9:16:09.652: Firmware stopped! You can only send host and shell commands until you hit emergency stop or restart the printer. Eventually running print is stopped.
    Mesg:9:16:09.652: //action:poweroff
    Mesg:9:16:14.316: Warning: Communication timeout - resetting communication buffer.
    Mesg:9:16:14.316: This means that a expected firmware response was not seen within the expected time.
    Mesg:9:16:14.316: The typical reason is a communication error and print should continue after the communication reset.
    Mesg:9:16:14.316: Connection status: Buffered:39, Manual Commands: 2, Job Commands: 6
    Mesg:9:16:14.316: Buffer used:39 Enforced free byte:0 lines stored:1
    Mesg:9:16:14.316: Firmware stopped! You can only send host and shell commands until you hit emergency stop or restart the printer.
    Mesg:9:16:14.316: Firmware stopped! You can only send host and shell commands until you hit emergency stop or restart the printer.
    Mesg:9:16:14.316: Firmware stopped! You can only send host and shell commands until you hit emergency stop or restart the printer.
    Mesg:9:16:14.316: Firmware stopped! You can only send host and shell commands until you hit emergency stop or restart the printer.
    Mesg:9:16:14.316: Firmware stopped! You can only send host and shell commands until you hit emergency stop or restart the printer.
    Mesg:9:16:14.316: Firmware stopped! You can only send host and shell commands until you hit emergency stop or restart the printer.
    Mesg:9:16:14.317: Firmware stopped! You can only send host and shell commands until you hit emergency stop or restart the printer.
    Exec:9:16:14.317: @stopLog

    June 12