TT_Vert
About
- Username
- TT_Vert
- Joined
- Visits
- 22
- Last Active
- Roles
- Member
Comments
-
Repetier said: Layer is only shown if you print through repetier-server and have it enabled to cycle through all. Host as printer daemon will only show ETA/ETE. I also want to follow up on this. Perhaps this is a bug but I star…
-
Ok I'm seriously starting to question my own insanity but I'm not going nuts and I have pics to prove it this time. I started a job on server this time, it showed a few lines of gcode commands and then just stopped in host.. Does it buffer them a…
-
Is that a feature that can be requested or is it difficult to implement it? Clearly it is aware of the layer and is able to send ETA, ETE already would it be hard for host to send that data along via M117 commands? Oddly, I closed host when I went…
-
Also I reinstalled host and now all commands are showing properly in real-time log so I have to assume they'll show in repetier.log when the time comes to log this error. I have a long list of prints to finish before I can cancel a print to log thi…
-
Turns out the PWM circuit took a dive on this board.
-
FYI this seems to occur for others as well. Maybe a marlin FW issue? https://github.com/andrivet/ADVi3pp-Marlin/issues/15
-
I am initiating all prints via host, none via server. I have no repetier.log file on my server (pi) Looking at the log session option in host it says "it will contain all communication even if disabled in log view". Oddly my log view has command…
-
Ok can you explain what you need then? This is the log generated by enabling what you told me to enable. Do i need to somehow change logging level to show what you want to see? I'll try to cancel a job and send a G28 to see if it homes where it s…
-
Thanks. I did actually flash ADVi earlier today and It does display M117 commands now. I'm new to repetier-host/server and many of my questions have to do w/ anomalies w/ this software (Start/end time the same in informer, showing UTC vs. local t…
-
Is there anything I can do to resolve this? No M117 commands will display a thing? All i can see when running M115 is Marlin V1; Sprinter/grbl mashup for gen6 and a firmware URL which goes to a defunct site. Dave
-
No idea how that happened. Here is the log again I assume it's around line 1660 10:29:46 I still don't see it attached. I see the log after i upload it to your site but when I submit it is gone. Here it is in my dropbox. https://www.dropbox.com/…
-
Ok here is the log. I started the job. I then canceled the job about 20 seconds into the print by clicking . The extruder was about mid axis on X when I stopped the job. I then went back to host and clicked print again and it started on the same…
-
Where would the log be? I don't see much on the gui console and I didn't see any logs in appdata or program files folders (Windows). Also seems it doesn't like the M107 either as the print cooling fan is always on. The repetier FW maker select …
-
Did it again to me today. Printed from host, had to cancel job from host due to an issue w/ print and then when I started it over if I homed X from the printer it thought where the print left off was home. I started a new print from host and it st…
-
BTW, it works fine on my Maker select V2.
-
I print from host.the gcode is still where it had been work my other printer (in cura)
-
Did you ave the settings? I noticed they aren't applied for me until I click save and re slice
-
Agreed. I had to silence all as its obnoxious at 3am. I need my phone volume on at all times so its not so easy just to silence phone.
-
Solved. After doing some research it seems there are issues w/ ffmpeg and Jessie. pointing to /usr/bin/avconv fixed the issue. Thanks for the help. So now the only issues unsolved are the cropping of webcam which you are aware of as well as th…
-
Thanks for this, very helpful in solving my issue.
-
I do have the correct path /home/pi/ffmpeg (As far as I know it's the only ffmpeg dir) so I don't know what is going on. With that said I noticed that while i see the camera (Dynamic image URL) and still shot (Static image) in printer settings in s…
-
Great Thanks much!!
-
If I click the eye I see the time lapse of the video sixth plays properly. I do have ffmpeg installed but unsure if it's configured properly. I did provide the correct path in global | time lapse but that's as far as I went, is there more config …
-
Either way I disabled my power off command as you can see by the attached Test gcode and it still says 0 failed for every single video
-
Sorry, I'm trying to understand this. How many commands will fill a 127 byte buffer? Why would the printer not run every command sent to it when it's in the buffer and then when done buffer the next set of commands, run them, etc. until no more c…
-
If this helps, here is the server.log for this print as well as the gcode I used (all prints see to do this however). I had to zip it as I could not attach the gcode properly. Same deal here Short 1 layer code w/ nothing other than the stock cura …
-
Just created a simple one line print w/o any of the wait commands and it also shows failed. Repetier-informer says job finished so I have no idea why the time-lapse says failed. Sometimes I get a good time-lapse others I just get the initial shot…
-
Where to add that (top or bottom)? I did add a wait command for 5 minutes before the 1ms waits. How does sleep 10 differ than the dwell commands already in place?
-
Great thank you for the nice product.
-
In keeping w/ my picture theme to make things easier. The repetier-server view shows full camera, 8080 ui shows full camera, host crops. The server pic was captured a bit after a print started so the image is different but size is correct.