Nandox7
About
- Username
- Nandox7
- Joined
- Visits
- 148
- Last Active
- Roles
- Member
Comments
-
Oh I definitely assume I screw up something with the configuration. Actually I just ruled out any hardware problem.I loaded Marlin4Due just to test it and it worked fine, all Axis working smooth as silk and no odd behavior. Now that I know that I d…
-
I kept checking their temperarure. And they were was always cold to the touch. That was right after turning on the printer. But it gets even more weird with the Y axis. That after any movement it keeps moving on it's own. In there I only made it…
-
Ok thanks for the help.I'll give that a try and report back after testing. Should Octoprint send these line numbers?I know that it was made to not only with Repetier but also with Marlin and other firmwares.Just trying to understand if this is somet…
-
Despite not using a servo to deploy a probe I also noticed problems moving to 0.92.8.In you case could be because the firmware doesn't know quite yet where it is in terms of Z position. I'd try and set the Z homing done before running G32.Call the …
-
My zmin endstop is the sensor probe, I have the probe connected to the zmin endstop in the ramps. Btw I have noticed a odd behavior in regards to the G28 Z0.If I have the printer in X0 Y0 and I do G28 Z0 it doesn't apply the Z_PROBE_X_OFFSET -and Z_…
-
UPDATE: It's getting better So if I only use G28 Z0 it gets to the proper height.As soon as I execute G32 (event without SX) it gets messed up and too high. I also notice some odd behavior with G32, as if it starts with a probe a bit high when it m…
-
Thanks for the warning.I assumed Sx could be used normally, I don't have a ZMax endstop so I can never determine Z Max Position. I have G32 set as default in the start GCode as it become annoying to always add/remove it when needed and the probingpr…
-
I've make sure to wipe the EEPROM every time I load the firmware. I run the EEPROM clear sketch from arduino before just to try and avoid any bad data in there. My Z MIN endstop was removed and the sensor connected to it's pin, so there is nothing o…
-
I have bed coating enabled for the UI but I actually checked and nothing is selected for it.As for bending correction it also has no values defined.From the settings shared in the previous post:---#define BENDING_CORRECTION_A 0#define BENDING_CORREC…
-
Yes I did, I see I made a typo in my previous post: :SIt should be: (can't edit the text now...)---G28 X0 Y0G1 X100 Y100 // So the probe is over the bedG28 Z // Tried also with Z0G32 S2---In regards to the Z Probe pin as endstop, it i…
-
Tried that and didnt't worked.---G28 X0 Y0G1 X100 Y100 // So the probe is over the bedG28 XG32 S2--- After this doing G1 Z0 leaves the nozzle several mm above the bed. After I did the exactly the same with 0.92.6 and it leaves the nozzle touching t…
-
No luck.Wiped EEPROM, loaded 0.92.8 and it prints in the air. My Z-PROBE Settings for 0.92.6: ---#define FEATURE_Z_PROBE 1#define Z_PROBE_Z_OFFSET 0#define Z_PROBE_Z_OFFSET_MODE 0#define Z_PROBE_BED_DISTANCE 10#define Z_PROBE_PIN ORIG_Z_MIN_PIN#defi…
-
I added it to the new configuration but later also made sure the value was fine in the EEPROM.I just wiped the EEPROM and loaded 0.92.6 as I needed to print and is working well. Going to give 0.92.8 another try, when I loaded it I didn't wiped the …
-
@MartinsZB, i also changed to Repetier from Marlin this week and after a few bumps all is working perfectly. I have a capacitance sensor but a inductive works the same in terms of FW.What I did was in part what @Repetier mentioned to use G28 X0 Y0 t…
-
@Repetier, thanks that would be great. At the moment I need to recall to lower the Z before a new print, because if it ends quite high in the Z axis the G32 takes a looot of time. But I have it all running fine now, just have to remember to updat…
-
Ok, I now have the things working more or less ok.But still there is some behaviour that seems odd. @Repetier you said that there is a Z probing position and I have found the params bellow:--- #define ZHOME_X_POS 130#define ZHOME_Y_POS 125---That i…
-
Ok, go it. So I just need to add the Gcode to run the autolevel in the print gcode. I already have Gcode that raises the Z, then does homing of XY so it prevent the head hitting the bed during it.I'll remove the Z homing and just leave the autolevel…
-
Hey, I'm trying to re-use this thread but if better I can create a new one. I have a cartesian printer and moving from Marlin where I have all working fine, so my hardware side of things is ok.I was reading the instructions but they are a bit confus…