EGropp
About
- Username
- EGropp
- Joined
- Visits
- 269
- Last Active
- Roles
- Member
Comments
-
I have looked over the doc in link 2 several times (i have even printed it so i can read it while offline..) What I read from the doc is.. If I set the probe X,Y points so position #1 is 20,20 position #2 is 150, 20 and position #3 is 20,250 The the…
-
here are my eeprom settings... I had to set the max x to 150 to get the autoleveling to not try to probe over the edge of the board (a bit disappointing as it seems that I will loose the ability to print closer than about 30mm from the edge..
-
I have had some difficulty actually understanding which extruder is used for 0,0. If i remove all offsets, and home X and Y, the true 0,0 would be physically located (on the bed) in the front left corner (the extruder would then hang off of the fron…
-
The Z probe is set to the right of the nozzles (this is a 3 extruder system). I will need to get a copy of the eeprom settings. Right now i have removed the outer nozzles because they were dragging on the print, I am trying to print corner bracke…
-
I had accidentally posted this in a different thread.. How do you change the measurement points for a G32 S2? (My Z-Probe is on the right side of the extruders) When I send the G32 S2, the calibration routine goes to these coordinates 16:54:51.378 …
-
Very sorry to hijack this thread (this was unintentional).. This post was supposed to have been put into the thread that I had opened a few days ago. I will be copying this post (and my responses to that thread)...
-
How do you change the measurement points for a G32 S2? (My Z-Probe is on the right side of the extruders) When I send the G32 S2, the calibration routine goes to these coordinates 16:54:51.378 : Z-probe:10.03 X:20.00 Y:20.0016:55:01.721 : Z-probe:10…
-
i have not yet taken manual measurements on the bed (i will do this tonight) to see where the discrepancies lie. I was hoping that I could get the autolevel process corrected so it would account for that (if i could set it up to use a mesh-map (i th…
-
ok.. I went back to try this again. Printing PLA, Bed is set to 60, extruder temp is set to 210 for the first layer and 205 for the reset of the layers. I did notice that in RH, there is a Slic3r and a Slicr3 Prusa versions. I had been setup to use …
-
Thank you.. Is there a configuration.h file located somewhere in the software? Or can it be generated from the existing machine? I am uncertain of some of the settings asked for in the configuration tool. So far this is an out of the box installati…
-
I have been searching several threads and youtube videos and I am getting lost in all of the data here. I see several posts on how to setup the Bed autoleveling, going through them, they all start the same, then they lose me when they start to talk…
-
calibration was done with bed and extruder heated (and the extruder was clean). Here is a screen grab of the video where it all fell apart...
-
Firmware version is .92.9.. I have been hunting the host firmware editor for probing locations and just not having any luck at all.
-
I am completely lost now. I see all of the references in this forum for setting the auto leveling functions (in a config.h file) i dont seem to have this file (I am running a windows 10 machine). I have looked in the registry and see nothing that w…
-
I thought that the gantry was the Y axis (which would make it E-W) and the bed depth was the X (making it N - S). I have an HE3D tri-extruder printer that I am working with
-
Looking at this interface, it would appear that X is defined as the width of the bed (from right to left) and Y is the depth of the bed (front to back). This makes no sense to me as the printers X is the depth (front to back) and Y is the width (lef…