power on graph extruder

Comments

• Repetier

  November 12

  This mainly depends on the printer firmware. Only if power is reported we show the power graph as green background. One case I know is klipper without api connection. In g-code mode klipper will not report power only via api object model.
• Bob_le_herisson

  November 12

  merci pour votre réponse
   je vais faire sans cette information, dommage car celui du bed est affiché, c'est pour celà que ça m'a interrogé 
  translate by google because I am french and old  
  Thank for your response 
  I'm going to do without this information, too bad because that of the bed is displayed, that's why it questioned me.
  
  Two emotion tech, Micro Delta Rework firmware "smoothieware" 
  Raspberry PI 4Go
  Repetier host 2.3.2
  Repetier server free 1.4.18
  Repetier server Monitor 1.4.7
• Repetier

  November 12

  You can check in console when you disable temperature filter you see what smoothieware reports. If you see that it reports power please copy paste some lines here. Maybe ther format is not correctly supported. Unfortunately not all firmwares do it the same.
• Bob_le_herisson

  November 12

  j'ai pris ça dans Repetier host pendant qu'il imprime
  

   I took this from Repetier host

  
  "
  

  15:11:11.581 : ok (N104470)

  15:11:11.628 : ok (N104471)

  15:11:11.628 : ok (N104472)

  15:11:11.628 : ok (N104473)

  15:11:11.722 : ok (N104474)

  15:11:11.722 : ok (N104475)

  15:11:11.925 : ok (N104476)

  15:11:11.941 : ok T:227.4 /225.0 @29 B:70.0 /70.0 @110 ; (N104477)

  15:11:12.035 : ok (N104478)

  15:11:12.035 : ok (N104479)

  15:11:12.035 : ok (N104480)

  15:11:12.035 : ok (N104481)

  15:11:12.035 : ok (N104482)

  15:11:12.035 : ok (N104483)

  15:11:12.035 : ok (N104484)

  "
• Bob_le_herisson

  November 12

  et ça dans repetier server
  

  ok (N111584)

  Send:14:14:17.080: N111585 G0 X-5.000 Y9.499

  Recv:14:14:17.089: ok (N111585)

  Send:14:14:17.089: N111586 G1 F3000 X-5.000 Y-9.408 E2356.02207

  Recv:14:14:17.597: ok (N111586)

  Send:14:14:17.597: N111587 M105

  Recv:14:14:17.598: ok T:228.6 /225.0 @0 B:70.0 /70.0 @38 (N111587)

  Send:14:14:17.598: N111588 G0 F9000 X-4.926 Y-9.266

  Recv:14:14:17.617: ok (N111588)

  Send:14:14:17.617: N111589 G0 X-6.269 Y-9.196

  Recv:14:14:17.619: ok (N111589)

  Send:14:14:17.619: N111590 G0 X-6.890 Y-10.025

  Recv:14:14:17.627: ok (N111590)
• Bob_le_herisson

  November 12 edited November 12

  M105

  Recv:15:29:00.834: ok T:232.0 /229.0 @0 B:70.0 /70.0 @41 (N243913)

  Send:15:29:00.834: N243914 G0 F9000 X22.763 Y9.505

  Recv:15:29:00.842: ok (N243914)

  Send:15:29:00.842: N243915 G1 F4080 X-2.452 Y-15.710 E7837.74357

  Recv:15:29:01.376: ok (N243915)

  Send:15:29:01.376: N243916 G0 F9000 X-3.668 Y-15.158

  Recv:15:29:01.386: ok (N243916)

  Send:15:29:01.386: N243917 G1 F4080 X22.022 Y10.532 E7838.71028

  Recv:15:29:01.932: ok (N243917)

  Send:15:29:01.932: N243918 M105

  Recv:15:29:01.933: ok T:232.0 /229.0 @0 B:70.0 /70.0 @107 (N243918)

  Send:15:29:01.933: N243919 G0 F9000 X21.210 Y11.487

  Recv:15:29:01.941: ok (N243919)

  Send:15:29:01.941: N243920 G1 F4080 X-4.893 Y-14.616 E7839.69252

  Recv:15:29:02.495: ok (N243920)

  Send:15:29:02.495: N243921 G0 F9000 X-6.091 Y-14.045

  Recv:15:29:02.505: ok (N243921)

  Send:15:29:02.505: N243922 G1 F4080 X20.322 Y12.368 E7840.68643

  Recv:15:29:03.062: ok (N243922)

  Send:15:29:03.062: N243923 M105

  Recv:15:29:03.064: ok T:231.7 /229.0 @255 B:70.0 /70.0 @189 (N243923)

  Send:15:29:03.064: N243924 G0 F9000 X24.646 Y6.085
  
  j'espère que je ne me trompe pas
  

  I hope I'm not wrong
  
  https://ibb.co/wYyhhZG  photo
  https://ibb.co/GnnfX0d 
  
• Repetier

  November 12

  Looks like there is a power for extruder but it is not visible. Often the value is 0 but not all the time so I would expect to see some spikes at least. I will investigate further.
• Repetier

  November 12

  Ok found it. Normally it is @:value but smoothieware uses @value and for T the case was not added. Should work in 1.5.0. 
• Bob_le_herisson

  November 12

  thank   you are the best 
  tout le reste fonctionne à merveille
  

  everything else works perfectly

  
  https://ibb.co/58ycBkQ
• Bob_le_herisson

  November 13

  Bonjour , c'est encore moi ! 

  Je suppose que dans Repetier host  onglet "courbe de température" les graphiques "sortie extrudeur" et "sortie plateau" c'est le même problème ?
  

  Hello, it’s me again! 
  I suppose that in Repetier host tab "temperature curve" the graphs "output extruder" 
  and "output bed" it's the same problem ?
  screen shot
  https://ibb.co/4mn0QFJ
• Repetier

  November 13

  Likely, have added it to my checklist for next update.