regression in current devel firmware - stops immediately claiming homing failed
in Bug Reports
Just switched from 1.0.4 to development firmware (via website generator) and printing on my X3D XL CoreXY printer fails immediately with log below. 1.0.4 worked just fine.
08:54:17.324 : N2 M530 S1 L366*58
08:54:17.324 : N3 M531 CFFFP_2_1_Tubus_5cm_ESP32-CAM*85
08:54:17.324 : N4 M117 ETE 5h 19m 07s*56
08:54:17.324 : N5 G21*31
08:54:17.324 : N6 G90*22
08:54:17.324 : N7 M82*30
08:54:17.324 : N8 G28 Z0*81
08:54:17.335 : N9 G28 X0 Y0*27
08:54:17.337 : N10 G1 Z15 S100*37
08:54:17.340 : N11 G32 S2*105
08:54:17.368 : N12 G92 E0*116
08:54:17.368 : N13 G1 F200 E3*24
08:54:17.369 : N14 G92 E0*114
08:54:17.369 : N15 M117 Printing...*47
08:54:18.630 : RequestStop:
08:54:18.657 : fatal:Homing failed! - Printer stopped and heaters disabled due to this error. Fix error and restart with M999.
08:54:18.660 : fatal:Homing failed! - Printer stopped and heaters disabled due to this error. Fix error and restart with M999.
08:54:18.660 : N16 G28 Z0*110
08:54:18.668 : fatal:Homing failed! - Printer stopped and heaters disabled due to this error. Fix error and restart with M999.
08:54:18.671 : N17 M104 S0 T0*23
08:54:18.680 : fatal:Homing failed! - Printer stopped and heaters disabled due to this error. Fix error and restart with M999.
08:54:18.688 : fatal:Homing failed! - Printer stopped and heaters disabled due to this error. Fix error and restart with M999.
08:54:18.701 : fatal:Homing failed! - Printer stopped and heaters disabled due to this error. Fix error and restart with M999.
08:54:18.702 : N18 M140 S0*92
08:54:18.702 : N19 M530 S0*94
08:54:18.709 : fatal:Homing failed! - Printer stopped and heaters disabled due to this error. Fix error and restart with M999.
08:54:18.717 : Error:Checksum required when switching back to ASCII protocol.
08:54:18.717 : Resend:15
08:54:18.741 : Resend: N15 M117 Printing...*47
08:54:18.741 : Resend: N16 G28 Z0*110
08:54:18.741 : Resend: N17 M104 S0 T0*23
08:54:18.741 : Resend: N18 M140 S0*92
08:54:18.741 : Resend: N19 M530 S0*94
08:54:18.754 : fatal:Homing failed! - Printer stopped and heaters disabled due to this error. Fix error and restart with M999.
08:54:18.766 : fatal:Homing failed! - Printer stopped and heaters disabled due to this error. Fix error and restart with M999.
08:54:18.775 : fatal:Homing failed! - Printer stopped and heaters disabled due to this error. Fix error and restart with M999.
08:54:18.788 : fatal:Homing failed! - Printer stopped and heaters disabled due to this error. Fix error and restart with M999.
08:54:18.795 : fatal:Homing failed! - Printer stopped and heaters disabled due to this error. Fix error and restart with M999.
Comments