Problème pour imprimé

KevinC

Bonjour,

J’ai un souci avec mon imprimante,

Je viens de mètre un raspberry pi avec repetier server

j'ai un message qui me dit que j'ai un problème avec le matériel de mon imprimante.

Ce qui m'empêche d'imprimer avec repetier server.

Par contre avec une carte sd j'ai aucuns soucis

Je vous joins donc une capture d'écran du message

Pourquoi sur carte SD j'ai 0 problème et sur repetier server j'ai ce problème ?

Pouvez-vous m'aider à corriger ce problème s'il vous plais.

https://gyazo.com/e40f8c5ff8fc852b08733e0256387ab4

Repetier

The M99 being metntioned triggers the error.

Question would be why you get a crc error - haven't seen this yet so think it is firmware internal check maybe from eeprom as that uses crc error checks. So it might be that eeprom is not working or if configured to use sd card you just have no sd card inserted.

If that only happens at connection start it should recover when you send "Try to recover" - otherwise search in installation directory/firmwares the file marlin.xml for rule

<response type="conditionIgnoring">(.M999\b.)</response>

and add before that line

<response type="ignore">enqueu?e?(ing)?.(.M999\b.*)</response>

That should disable the message. At least if it comes from M999 and not because the complete line starts with error: as that is still a firmware error. If you can please post the console output when you connect with all filters disabled, especially the part around the error message.

KevinC

Bonjour,

Quand je mets la carte sd ou que je enlève la carte sd j'ai le même message.
Si je fais Try to recover le message revient à chaque fois.

Ce qui est bizarre c'est que la 6 mois j’utilisai déjà repetier server et donc c'était la version 1.2.1
Faut-t'il peut-être que je réinstalle complètement au propre repetier server sur mon raspberry ?

Repetier

You can use the update function in Repetier-Server to update. No need for new install. But you might need to add the change to get rid of the message. But you haven't posted the console log when it happens so can not say if that even would help. But selecting try recover should at least make message in server disappear and you can use it. Just as I said something with eeprom settings might be wrong or something else. Guess the console log will show it better what is causing it.

KevinC

https://gyazo.com/71cbe4462b42c694c72acc497c94a51f

Repetier

If you do it in terminal you need to first open the marlin.xml file in a text editor:

sudo nano /usr/local/Repetier-Server/firmware/marlin.xml

then search for the line mentioned and add that line before it. Save and exit editor, then reboot pi.
After any update the change will be gone, but in next release I'll add it.

KevinC

<a rel="nofollow" target="blank">Repetier</a> said:

If you do it in terminal you need to first open the marlin.xml file in a text editor:

sudo nano /usr/local/Repetier-Server/firmware/marlin.xml

then search for the line mentioned and add that line before it. Save and exit editor, then reboot pi.
After any update the change will be gone, but in next release I'll add it.

ceci ?

https://gyazo.com/f982c1b6e4fd7ad16d7857b3d5d9a503

Repetier

No, one line higher that is important.

And please show me the console log of the printer for better assistance.

KevinC

https://gyazo.com/95a17776555034a311dad119ece42c0d

KevinC

<a rel="nofollow" target="blank">Repetier</a> said:

The M99 being metntioned triggers the error.

Question would be why you get a crc error - haven't seen this yet so think it is firmware internal check maybe from eeprom as that uses crc error checks. So it might be that eeprom is not working or if configured to use sd card you just have no sd card inserted.

If that only happens at connection start it should recover when you send "Try to recover" - otherwise search in installation directory/firmwares the file marlin.xml for rule
<response type="conditionIgnoring">(.M999\b.)</response>
and add before that line
<response type="ignore">enqueu?e?(ing)?.(.M999\b.*)</response>
That should disable the message. At least if it comes from M999 and not because the complete line starts with error: as that is still a firmware error. If you can please post the console output when you connect with all filters disabled, especially the part around the error message.

https://gyazo.com/b13436688bafc6c8abc81d4992976a42

Repetier

Sorry still too low, I meant above this line

<response type="conditionIgnoring">(.M999\b.)</response>

looks like it is 5 lines higher.

When I talk about the printer console I do not mean the terminal you showed. I mean when you are in the printer windows there is a tab console at least in english. That is where you see what printer says if you disable the filter.

KevinC

https://gyazo.com/9fd02c2a60ac63d737e998c6224cce9e

Repetier

yes

KevinC

merci vous avez corriger mon problème je peut imprimer maintenant
:) :)