hi
i'm using arduino mega and ramps 1.6 and i want attached laser module to my 3D printer as i need to activat air assist option for lightburn software
but i'm getting an error while confuigure coolant control option m7/m8
Coolant Control
*
Add the M7, M8, and M9 commands to turn mist or flood coolant on and off.
*
Note: COOLANT_MIST_PIN and/or COOLANT_FLOOD_PIN must also be defined.
*/
#define COOLANT_CONTROL
#if ENABLED(COOLANT_CONTROL)
#define COOLANT_MIST // Enable if mist coolant is present
#define COOLANT_FLOOD // Enable if flood coolant is present
#define COOLANT_MIST_INVERT false // Set "true" if the on/off function is reversed
#define COOLANT_FLOOD_INVERT false // Set "true" if the on/off function is reversed
#endif
her below the error message
it's asking to figurout the M7/M8 pin
i'm beganner so i have no much experiance
please your help will be thankfull
> Executing task in folder MEGA:
C:\Users\ahmed.platformio\penv\Scripts\pio.exe run <
Processing mega2560 (platform: atmelavr; board:
megaatmega2560; framework: arduino)
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------Verbose
mode can be enabled via -v, --verbose option
CONFIGURATION:
https://docs.platformio.org/page/boards/atmelavr/megaatmega2560.html</p>
PLATFORM: Atmel AVR (3.0.0) > Arduino Mega or Mega 2560
ATmega2560 (Mega 2560)
HARDWARE: ATMEGA2560 16MHz, 8KB RAM, 248KB Flash
DEBUG: Current (avr-stub) On-board (avr-stub, simavr)
PACKAGES:
-
framework-arduino-avr 5.1.0
- toolchain-atmelavr
1.50400.190710 (5.4.0)
Converting Marlin.ino
LDF: Library Dependency Finder ->
http://bit.ly/configure-pio-ldf</p>
LDF Modes: Finder ~ chain, Compatibility ~ soft
Found 5 compatible libraries
Scanning dependencies...
Dependency Graph
|-- <Wire> 1.0
|-- <SPI> 1.0
|-- <EEPROM> 2.0
|-- <SoftwareSerial> 1.0
Building in release mode
Compiling .pio\build\mega2560\src\src\MarlinCore.cpp.o
Compiling
.pio\build\mega2560\src\src\gcode\config\M221.cpp.o
Compiling
.pio\build\mega2560\src\src\gcode\config\M301.cpp.o
Compiling
.pio\build\mega2560\src\src\gcode\config\M302.cpp.o
In file included from
Marlin\src\inc/../HAL/./AVR/HAL.h:22:0,
from
Marlin\src\inc/../HAL/HAL.h:26,
from
Marlin\src\inc/MarlinConfig.h:31,
from
Marlin\src\MarlinCore.h:24,
from
Marlin\src\MarlinCore.cpp:31:
Marlin\src\MarlinCore.cpp: In function 'void setup()':
Marlin\src\inc/../HAL/./AVR/fastio.h:87:35: error:
'DIOCOOLANT_MIST_PIN_DDR' was not declared in this scope
#define
_SET_OUTPUT(IO) SBI(DIO ## IO ##
_DDR, DIO ## IO ## _PIN)
^
Marlin\src\inc/../HAL/./AVR/../shared/Marduino.h:48:21:
note: in definition of macro 'SBI'
#define SBI(A,B) (A
|= (1 << (B)))
^
Marlin\src\inc/../HAL/./AVR/fastio.h:108:31: note: in
expansion of macro '_SET_OUTPUT'
#define
SET_OUTPUT(IO) _SET_OUTPUT(IO)
^
Marlin\src\inc/../HAL/./AVR/fastio.h:114:35: note: in
expansion of macro 'SET_OUTPUT'
#define
OUT_WRITE(IO,V) do{ SET_OUTPUT(IO);
WRITE(IO,V); }while(0)
^
Marlin\src\MarlinCore.cpp:1145:5: note: in expansion of
macro 'OUT_WRITE'
OUT_WRITE(COOLANT_MIST_PIN, COOLANT_MIST_INVERT); // Init Mist Coolant OFF
^
Marlin\src\inc/../HAL/./AVR/fastio.h:87:54: error:
'DIOCOOLANT_MIST_PIN_PIN' was not declared in this scope
#define
_SET_OUTPUT(IO) SBI(DIO ## IO ##
_DDR, DIO ## IO ## _PIN)
^
Marlin\src\inc/../HAL/./AVR/../shared/Marduino.h:48:33:
note: in definition of macro 'SBI'
#define SBI(A,B) (A
|= (1 << (B)))
^
Marlin\src\inc/../HAL/./AVR/fastio.h:108:31: note: in
expansion of macro '_SET_OUTPUT'
#define
SET_OUTPUT(IO) _SET_OUTPUT(IO)
^
Marlin\src\inc/../HAL/./AVR/fastio.h:114:35: note: in
expansion of macro 'SET_OUTPUT'
#define
OUT_WRITE(IO,V) do{ SET_OUTPUT(IO);
WRITE(IO,V); }while(0)
^
Marlin\src\MarlinCore.cpp:1145:5: note: in expansion of
macro 'OUT_WRITE'
OUT_WRITE(COOLANT_MIST_PIN, COOLANT_MIST_INVERT); // Init Mist Coolant OFF
^
In file included from
Marlin\src\inc/../HAL/./AVR/HAL.h:24:0,
from
Marlin\src\inc/../HAL/HAL.h:26,
from
Marlin\src\inc/MarlinConfig.h:31,
from
Marlin\src\MarlinCore.h:24,
from
Marlin\src\MarlinCore.cpp:31:
Marlin\src\inc/../HAL/./AVR/fastio.h:82:41: error:
'DIOCOOLANT_MIST_PIN_RPORT' was not declared in this scope
#define
_WRITE(IO,V) do{ if (&(DIO
IO ## _RPORT) < (uint8_t*)0x100) _WRITE_NC(IO,V); else _WRITE_C(IO,V);
}while(0)
^
Marlin\src\inc/../HAL/./AVR/fastio.h:102:31: note: in
expansion of macro '_WRITE'
#define
WRITE(IO,V) _WRITE(IO,V)
^
Marlin\src\inc/../HAL/./AVR/fastio.h:114:51: note: in
expansion of macro 'WRITE'
#define
OUT_WRITE(IO,V) do{ SET_OUTPUT(IO);
WRITE(IO,V); }while(0)
^
Marlin\src\MarlinCore.cpp:1145:5: note: in expansion of
macro 'OUT_WRITE'
OUT_WRITE(COOLANT_MIST_PIN, COOLANT_MIST_INVERT); // Init Mist Coolant OFF
^
In file included from Marlin\src\inc/../HAL/./AVR/HAL.h:22:0,
from
Marlin\src\inc/../HAL/HAL.h:26,
from
Marlin\src\inc/MarlinConfig.h:31,
from
Marlin\src\MarlinCore.h:24,
from
Marlin\src\MarlinCore.cpp:31:
Marlin\src\inc/../HAL/./AVR/fastio.h:72:14: error:
'DIOCOOLANT_MIST_PIN_WPORT' was not declared in this scope
if (V) SBI(DIO ##
IO ## _WPORT, DIO ## IO ## _PIN); </p>
^
Marlin\src\inc/../HAL/./AVR/../shared/Marduino.h:48:21:
note: in definition of macro 'SBI'
#define SBI(A,B) (A
|= (1 << (B)))
^
Marlin\src\inc/../HAL/./AVR/fastio.h:82:81: note: in
expansion of macro '_WRITE_NC'
#define
_WRITE(IO,V) do{ if (&(DIO
IO ## _RPORT) < (uint8_t*)0x100) _WRITE_NC(IO,V); else _WRITE_C(IO,V);
}while(0)
^
Marlin\src\inc/../HAL/./AVR/fastio.h:102:31: note: in
expansion of macro '_WRITE'
#define
WRITE(IO,V) _WRITE(IO,V)
^
Marlin\src\inc/../HAL/./AVR/fastio.h:114:51: note: in
expansion of macro 'WRITE'
#define
OUT_WRITE(IO,V) do{ SET_OUTPUT(IO);
WRITE(IO,V); }while(0)
^
Marlin\src\MarlinCore.cpp:1145:5: note: in expansion of
macro 'OUT_WRITE'
OUT_WRITE(COOLANT_MIST_PIN, COOLANT_MIST_INVERT); // Init Mist Coolant OFF
^
Marlin\src\inc/../HAL/./AVR/fastio.h:73:14: error:
'DIOCOOLANT_MIST_PIN_WPORT' was not declared in this scope
else CBI(DIO ## IO ## _WPORT, DIO ## IO ## _PIN);
</p>
^
Marlin\src\inc/../HAL/./AVR/../shared/Marduino.h:52:21:
note: in definition of macro 'CBI'
#define CBI(A,B) (A
&= ~(1 << (B)))
^
Marlin\src\inc/../HAL/./AVR/fastio.h:82:81: note: in
expansion of macro '_WRITE_NC'
#define
_WRITE(IO,V) do{ if (&(DIO
IO ## _RPORT) < (uint8_t*)0x100) _WRITE_NC(IO,V); else _WRITE_C(IO,V);
}while(0)
^
Marlin\src\inc/../HAL/./AVR/fastio.h:102:31: note: in
expansion of macro '_WRITE'
#define
WRITE(IO,V) _WRITE(IO,V)
^
Marlin\src\inc/../HAL/./AVR/fastio.h:114:51: note: in
expansion of macro 'WRITE'
#define
OUT_WRITE(IO,V) do{ SET_OUTPUT(IO);
WRITE(IO,V); }while(0)
^
Marlin\src\MarlinCore.cpp:1145:5: note: in expansion of
macro 'OUT_WRITE'
OUT_WRITE(COOLANT_MIST_PIN, COOLANT_MIST_INVERT); // Init Mist Coolant OFF
^
compilation terminated due to -fmax-errors=5.
*** [.pio\build\mega2560\src\src\MarlinCore.cpp.o] Error 1
===========================================================================
[FAILED] Took 9.26 seconds
===========================================================================
Environment
Status Duration
-------------
-------- ------------
mega2560
FAILED 00:00:09.257
======================================================================
1 failed, 0 succeeded in 00:00:09.257
======================================================================The
terminal process "C:\Users\ahmed.platformio\penv\Scripts\pio.exe
'run'" terminated with exit code: 1.
Terminal will be reused by tasks, press any key to close it.
