Hello, how to add additional A B C axis ?

FlyNuga

How i can add A B C axis in repetier firmware dev2 ?

Repetier

In crease in configuration.h

NUM_AXES to 5, 6, 7 for A, B, C and define the corresponding motors in configuration_io and also make sure to add them in

#define MOTORS </div>

{ &XMotor, &YMotor, &ZMotor, &E1Motor, &E2Motor }

#define MOTOR_NAMES </div>

{ PSTR("X"), PSTR("Y"), PSTR("Z"), PSTR("E0"), PSTR("E1") }

Motor names are AMotor, BMotor and CMotor you need to define.
That is actually all needed to have them.

For what are they needed? Often it is better to not have them and just switch E motor with that motor. Every extra motor adds code for stepping etc so motions get reduced max. speed from this. If you need them all to move same time that is the way to go. But e.g. for small adjustments or clearing plate you would sore them as E motor use function and restore e motor. Of course then requires own special gcodes to make sense of it.

FlyNuga

In file included from src\Repetier.h:480:0,

from src\Configuration.cpp:29:

src\motion/MotionLevel3.h: In static member function 'static void Motion3::unstepMotors()':

src\motion/MotionLevel3.h:117:9: error: 'AMotor' was not declared in this scope

AMotor.unstep();

_~~

src\motion/MotionLevel3.h:117:9: note: suggested alternative: 'ZMotor'

AMotor.unstep();

_~~

ZMotor

src\motion/MotionLevel3.h:120:9: error: 'BMotor' was not declared in this scope

BMotor.unstep();

_~~

src\motion/MotionLevel3.h:120:9: note: suggested alternative: 'ZMotor'

BMotor.unstep();

_~~

ZMotor

In file included from src/Repetier.h:480:0,

from src\PrinterTypes\Printer.cpp:19:

src/motion/MotionLevel3.h: In static member function 'static void Motion3::unstepMotors()':

src/motion/MotionLevel3.h:117:9: error: 'AMotor' was not declared in this scope

AMotor.unstep();

_~~

src/motion/MotionLevel3.h:117:9: note: suggested alternative: 'ZMotor'

AMotor.unstep();

_~~

ZMotor

src/motion/MotionLevel3.h:120:9: error: 'BMotor' was not declared in this scope

BMotor.unstep();

_~~

src/motion/MotionLevel3.h:120:9: note: suggested alternative: 'ZMotor'

BMotor.unstep();

_~~

ZMotor

In file included from src/Repetier.h:480:0,

from src\PrinterTypes\PrinterTypeCartesian.cpp:19:

src/motion/MotionLevel3.h: In static member function 'static void Motion3::unstepMotors()':

src/motion/MotionLevel3.h:117:9: error: 'AMotor' was not declared in this scope

AMotor.unstep();

_~~

src/motion/MotionLevel3.h:117:9: note: suggested alternative: 'ZMotor'

AMotor.unstep();

_~~

ZMotor

src/motion/MotionLevel3.h:120:9: error: 'BMotor' was not declared in this scope

BMotor.unstep();

_~~

src/motion/MotionLevel3.h:120:9: note: suggested alternative: 'ZMotor'

BMotor.unstep();

_~~

ZMotor

In file included from src/Repetier.h:480:0,

from src\PrinterTypes\PrinterTypeCoreXYZ.cpp:19:

src/motion/MotionLevel3.h: In static member function 'static void Motion3::unstepMotors()':

src/motion/MotionLevel3.h:117:9: error: 'AMotor' was not declared in this scope

AMotor.unstep();

_~~

src/motion/MotionLevel3.h:117:9: note: suggested alternative: 'ZMotor'

AMotor.unstep();

_~~

ZMotor

src/motion/MotionLevel3.h:120:9: error: 'BMotor' was not declared in this scope

BMotor.unstep();

_~~

src/motion/MotionLevel3.h:120:9: note: suggested alternative: 'ZMotor'

BMotor.unstep();

_~~

ZMotor

In file included from src/Repetier.h:480:0,

from src\PrinterTypes\PrinterTypeDelta.cpp:19:

src/motion/MotionLevel3.h: In static member function 'static void Motion3::unstepMotors()':

src/motion/MotionLevel3.h:117:9: error: 'AMotor' was not declared in this scope

AMotor.unstep();

_~~

src/motion/MotionLevel3.h:117:9: note: suggested alternative: 'ZMotor'

AMotor.unstep();

_~~

ZMotor

src/motion/MotionLevel3.h:120:9: error: 'BMotor' was not declared in this scope

BMotor.unstep();

_~~

src/motion/MotionLevel3.h:120:9: note: suggested alternative: 'ZMotor'

BMotor.unstep();

_~~

ZMotor

src\PrinterTypes\PrinterTypeDelta.cpp: In static member function 'static void PrinterType::restoreFromConfiguration()':

src\PrinterTypes\PrinterTypeDelta.cpp:322:17: error: 'BED_RADIUS' was not declared in this scope

bedRadius = BED_RADIUS;

~~~~_~~

In file included from src/Repetier.h:480:0,

from src\PrinterTypes\PrinterTypeDualXAxis.cpp:36:

src/motion/MotionLevel3.h: In static member function 'static void Motion3::unstepMotors()':

src/motion/MotionLevel3.h:117:9: error: 'AMotor' was not declared in this scope

AMotor.unstep();

_~~

*** [.pio\build\due\src\Configuration.cpp.o] Error 1

src/motion/MotionLevel3.h:117:9: note: suggested alternative: 'ZMotor'

AMotor.unstep();

_~~

ZMotor

src/motion/MotionLevel3.h:120:9: error: 'BMotor' was not declared in this scope

BMotor.unstep();

_~~

*** [.pio\build\due\src\PrinterTypes\PrinterTypeCartesian.cpp.o] Error 1

*** [.pio\build\due\src\PrinterTypes\PrinterTypeCoreXYZ.cpp.o] Error 1

src/motion/MotionLevel3.h:120:9: note: suggested alternative: 'ZMotor'

BMotor.unstep();

_~~

ZMotor

src\PrinterTypes\PrinterTypeDelta.cpp:322:17: note: suggested alternative: 'E_AXIS'

bedRadius = BED_RADIUS;

~~~~_~~

E_AXIS

*** [.pio\build\due\src\PrinterTypes\Printer.cpp.o] Error 1

In file included from src/Repetier.h:480:0,

from src\SdFat\FatLib\FatFile.cpp:25:

src/motion/MotionLevel3.h: In static member function 'static void Motion3::unstepMotors()':

src/motion/MotionLevel3.h:117:9: error: 'AMotor' was not declared in this scope

AMotor.unstep();

_~~

src/motion/MotionLevel3.h:117:9: note: suggested alternative: 'ZMotor'

AMotor.unstep();

_~~

ZMotor

src/motion/MotionLevel3.h:120:9: error: 'BMotor' was not declared in this scope

BMotor.unstep();

_~~

src/motion/MotionLevel3.h:120:9: note: suggested alternative: 'ZMotor'

BMotor.unstep();

_~~

ZMotor

In file included from src/Repetier.h:480:0,

from src\SdFat\FatLib\FatFileLFN.cpp:25:

src/motion/MotionLevel3.h: In static member function 'static void Motion3::unstepMotors()':

src/motion/MotionLevel3.h:117:9: error: 'AMotor' was not declared in this scope

AMotor.unstep();

_~~

src/motion/MotionLevel3.h:117:9: note: suggested alternative: 'ZMotor'

AMotor.unstep();

_~~

ZMotor

src/motion/MotionLevel3.h:120:9: error: 'BMotor' was not declared in this scope

BMotor.unstep();

_~~

*** [.pio\build\due\src\PrinterTypes\PrinterTypeDelta.cpp.o] Error 1

*** [.pio\build\due\src\PrinterTypes\PrinterTypeDualXAxis.cpp.o] Error 1

src/motion/MotionLevel3.h:120:9: note: suggested alternative: 'ZMotor'

BMotor.unstep();

_~~

ZMotor

*** [.pio\build\due\src\SdFat\FatLib\FatFileLFN.cpp.o] Error 1

*** [.pio\build\due\src\SdFat\FatLib\FatFile.cpp.o] Error 1

FlyNuga

i get errors

RAyWB

https://docfirmwarev2.repetier.com/config/motors<br/>

Repetier

You did not add one of the motor definition RAyWB showed you in configuration_io.h so AMotor is not defined causing the errors. They get defined same as x,y z motor but you need to add them.