Enable Z-probing

cagdas

The sensor is X + 20 away from the extruder. This is the settings I made. I'm getting an error

cagdas

<?xml version="1.0" encoding="utf-8"?>

<Repetier-Firmware-EEPROM>

<epr pos="1028" type="0" value="10">Language</epr>

<epr pos="75" type="2" value="115200">Baudrate</epr>

<epr pos="129" type="3" value="949.004">Filament printed</epr>

<epr pos="125" type="2" value="1021047">Printer active</epr>

<epr pos="79" type="2" value="0">Max. inactive time</epr>

<epr pos="83" type="2" value="360000">Stop stepper after inactivity</epr>

<epr pos="3" type="3" value="200.0000">X-axis steps per mm</epr>

<epr pos="7" type="3" value="200.0000">Y-axis steps per mm</epr>

<epr pos="11" type="3" value="800.0000">Z-axis steps per mm</epr>

<epr pos="15" type="3" value="200.000">X-axis max. feedrate</epr>

<epr pos="19" type="3" value="200.000">Y-axis max. feedrate</epr>

<epr pos="23" type="3" value="2.000">Z-axis max. feedrate</epr>

<epr pos="27" type="3" value="40.000">X-axis homing feedrate</epr>

<epr pos="31" type="3" value="40.000">Y-axis homing feedrate</epr>

<epr pos="35" type="3" value="2.000">Z-axis homing feedrate</epr>

<epr pos="145" type="3" value="200.000">X max length</epr>

<epr pos="149" type="3" value="200.000">Y max length</epr>

<epr pos="153" type="3" value="120.000">Z max length</epr>

<epr pos="1056" type="3" value="0.000">Park position X</epr>

<epr pos="1060" type="3" value="0.000">Park position Y</epr>

<epr pos="1064" type="3" value="10.000">Park position Z raise</epr>

<epr pos="51" type="3" value="1000.000">X-axis acceleration</epr>

<epr pos="55" type="3" value="1000.000">Y-axis acceleration</epr>

<epr pos="59" type="3" value="100.000">Z-axis acceleration</epr>

<epr pos="63" type="3" value="1000.000">X-axis travel acceleration</epr>

<epr pos="67" type="3" value="1000.000">Y-axis travel acceleration</epr>

<epr pos="71" type="3" value="100.000">Z-axis travel acceleration</epr>

<epr pos="1024" type="3" value="0.000">Coating thickness</epr>

<epr pos="808" type="3" value="2.000">Z-probe height</epr>

<epr pos="929" type="3" value="10.000">Max. z-probe - bed dist.</epr>

<epr pos="812" type="3" value="2.000">Z-probe speed</epr>

<epr pos="840" type="3" value="150.000">Z-probe x-y-speed</epr>

<epr pos="800" type="3" value="20.000">Z-probe offset x</epr>

<epr pos="804" type="3" value="0.000">Z-probe offset y</epr>

<epr pos="816" type="3" value="0.000">Z-probe X1</epr>

<epr pos="820" type="3" value="0.000">Z-probe Y1</epr>

<epr pos="824" type="3" value="160.000">Z-probe X2</epr>

<epr pos="828" type="3" value="0.000">Z-probe Y2</epr>

<epr pos="832" type="3" value="0.000">Z-probe X3</epr>

<epr pos="836" type="3" value="160.000">Z-probe Y3</epr>

<epr pos="1036" type="3" value="0.000">Z-probe bending correction A</epr>

<epr pos="1040" type="3" value="0.000">Z-probe bending correction B</epr>

<epr pos="1044" type="3" value="0.000">Z-probe bending correction C</epr>

<epr pos="880" type="0" value="0">Autolevel active (1/0)</epr>

<epr pos="1048" type="1" value="55">Bed Preheat temp.</epr>

<epr pos="106" type="0" value="0">Bed Heat Manager</epr>

<epr pos="107" type="0" value="255">Bed PID drive max</epr>

<epr pos="124" type="0" value="80">Bed PID drive min</epr>

<epr pos="120" type="0" value="255">Bed PID max value</epr>

<epr pos="1020" type="0" value="0">Enable retraction conversion</epr>

<epr pos="992" type="3" value="3.000">Retraction length</epr>

<epr pos="1000" type="3" value="40.000">Retraction speed</epr>

<epr pos="1004" type="3" value="0.000">Retraction z-lift</epr>

<epr pos="1008" type="3" value="0.000">Extra extrusion on undo retract</epr>

<epr pos="1016" type="3" value="20.000">Retraction undo speed</epr>

<epr pos="200" type="3" value="370.000">Extr.1 steps per mm</epr>

<epr pos="204" type="3" value="50.000">Extr.1 max. feedrate</epr>

<epr pos="208" type="3" value="20.000">Extr.1 start feedrate</epr>

<epr pos="212" type="3" value="5000.000">Extr.1 acceleration</epr>

<epr pos="294" type="1" value="190">Extr.1 Preheat temp.</epr>

<epr pos="216" type="0" value="3">Extr.1 heat manager</epr>

<epr pos="217" type="0" value="230">Extr.1 PID drive max</epr>

<epr pos="245" type="0" value="40">Extr.1 PID drive min</epr>

<epr pos="230" type="0" value="255">Extr.1 PID max value</epr>

<epr pos="231" type="2" value="0">Extr.1 X-offset</epr>

<epr pos="235" type="2" value="0">Extr.1 Y-offset</epr>

<epr pos="290" type="2" value="0">Extr.1 Z-offset</epr>

<epr pos="239" type="1" value="1">Extr.1 temp. stabilize time</epr>

<epr pos="250" type="1" value="150">Extr.1 temp. for retraction when heating</epr>

<epr pos="252" type="1" value="0">Extr.1 distance to retract when heating</epr>

<epr pos="254" type="0" value="255">Extr.1 extruder cooler speed</epr>

</Repetier-Firmware-EEPROM>

Repetier

And why don't you tell us what error you get and during which operation and what exactly you did :-)

cagdas

Repetier wrote
And why don't you tell us what error you get and during which operation and what exactly you did :-)

G32

Could not activate z-probe offset due to coordinate constraints - result is inaccurate

cagdas

09:19:45.847 : Info:Autoleveling disabled

09:19:50.238 : Z-probe:0.607 X:20.00 Y:0.00

09:19:53.238 : Z-probe:0.457 X:20.00 Y:45.00

09:19:56.072 : Z-probe:0.312 X:20.00 Y:90.00

09:19:58.868 : Z-probe:0.248 X:20.00 Y:135.00

09:20:01.595 : Z-probe:0.190 X:20.00 Y:180.00

09:20:05.244 : Z-probe:0.443 X:60.00 Y:0.00

09:20:08.051 : Z-probe:0.273 X:60.00 Y:45.00

09:20:10.712 : Z-probe:0.130 X:60.00 Y:90.00

09:20:13.320 : RequestStop:

09:20:18.358 : fatal:G32 leveling failed! - Printer stopped and heaters disabled due to this error. Fix error and restart with M999.

Repetier

You need to consider that your z probe is 20mm to the right, so it needs to move 20mm left. Make sure start position is at least x=20 to activate. Also make sure xy area for probing fits into reachable positions with that offset.

Also which might be more likely here increase z probe bed distance so probe can untrigger when going up. I think your bed is so much tilted that at the next point it was already triggered. 0.13mm distance before that point is not much of a gap to untrigger the sensor.

cagdas

Repetier wrote
You need to consider that your z probe is 20mm to the right, so it needs to move 20mm left. Make sure start position is at least x=20 to activate. Also make sure xy area for probing fits into reachable positions with that offset.

Also which might be more likely here increase z probe bed distance so probe can untrigger when going up. I think your bed is so much tilted that at the next point it was already triggered. 0.13mm distance before that point is not much of a gap to untrigger the sensor.

The extruder is above the orange shaded area.

In the orange shaded area, it does not stick to the plastic tray.

https://imgur.com/a/CX0ALbt<br/>

Repetier

As long as it is not finished with autoleveling it has no effect. You really need to start G32 at a higher Z so it succeeds.