Error:Line Number is not Last Line Number+1, Last Line:

Emelinej

Bonjour à tous,

Voici mon problème:

15:27:22.071 : Impression couche layer 3 sur 3
15:27:22.071 : N297 G1 F50 X49.644 Y54.649 E4.413260
15:27:22.071 : N298 G1 X49.644 Y55.217 E4.422195
15:27:22.071 : N299 G1 X49.645 Y55.946 E4.43353103
15:27:22.071 : N300 G1 X49.647 Y57.09 E4.4514684
15:27:22.071 : N301 G1 X49.648 Y57.589 E4.45928103
15:27:22.071 : N302 G1 X49.65 Y59.024 E4.4817881
15:27:22.071 : N303 G1 X49.647 Y59.705 E4.49245110
15:27:22.071 : N304 G1 X49.644 Y60.209 E4.50035100
15:27:22.071 : N305 G1 X49.644 Y60.222 E4.50056105
15:27:22.071 : N306 G1 X49.649 Y60.742 E4.50871105
15:27:22.071 : N307 G1 X49.649 Y61.116 E4.51457103
15:27:22.071 : Error:checksum mismatch, Last Line: 300
15:27:22.086 : Resend: N301 G1 X49.648 Y57.589 E4.45928103
15:27:22.086 : Resend: N302 G1 X49.65 Y59.024 E4.4817881
15:27:22.086 : Resend: N303 G1 X49.647 Y59.705 E4.49245110
15:27:22.086 : Resend: N304 G1 X49.644 Y60.209 E4.50035100
15:27:22.086 : Resend: N305 G1 X49.644 Y60.222 E4.50056105
15:27:22.086 : Error:Line Number is not Last Line Number+1, Last Line: 300
15:27:22.102 : Resend: N301 G1 X49.648 Y57.589 E4.45928103
15:27:22.102 : Resend: N302 G1 X49.65 Y59.024 E4.4817881
15:27:22.102 : Resend: N303 G1 X49.647 Y59.705 E4.49245110
15:27:22.102 : Resend: N304 G1 X49.644 Y60.209 E4.50035100
15:27:22.102 : Resend: N305 G1 X49.644 Y60.222 E4.50056105
15:27:22.102 : Error:Line Number is not Last Line Number+1, Last Line: 300
15:27:22.118 : Resend: N301 G1 X49.648 Y57.589 E4.45928103
15:27:22.118 : Resend: N302 G1 X49.65 Y59.024 E4.4817881
15:27:22.118 : Resend: N303 G1 X49.647 Y59.705 E4.49245110
15:27:22.118 : Resend: N304 G1 X49.644 Y60.209 E4.50035100
15:27:22.118 : Error:Line Number is not Last Line Number+1, Last Line: 300
15:27:22.134 : Resend: N301 G1 X49.648 Y57.589 E4.45928103
15:27:22.134 : Resend: N302 G1 X49.65 Y59.024 E4.4817881
15:27:22.134 : Resend: N303 G1 X49.647 Y59.705 E4.49245110
15:27:22.134 : Resend: N304 G1 X49.644 Y60.209 E4.50035100
15:27:22.134 : Resend: N305 G1 X49.644 Y60.222 E4.50056105
15:27:22.134 : Error:Line Number is not Last Line Number+1, Last Line: 300
15:27:22.149 : Resend: N301 G1 X49.648 Y57.589 E4.45928103
15:27:22.149 : Resend: N302 G1 X49.65 Y59.024 E4.4817881
15:27:22.149 : Resend: N303 G1 X49.647 Y59.705 E4.49245110
15:27:22.149 : Resend: N304 G1 X49.644 Y60.209 E4.50035100
15:27:22.149 : Resend: N305 G1 X49.644 Y60.222 E4.50056105
15:27:22.149 : Error:Line Number is not Last Line Number+1, Last Line: 305
15:27:22.149 : Resend: N306 G1 X49.649 Y60.742 E4.50871105
15:27:22.149 : Resend: N307 G1 X49.649 Y61.116 E4.51457103
15:27:22.149 : N308 M117 FIN 4m 23s101
15:27:22.165 : Resend: N306 G1 X49.649 Y60.742 E4.50871105
15:27:22.165 : Resend: N307 G1 X49.649 Y61.116 E4.51457103
15:27:22.165 : Resend: N308 M117 FIN 4m 23s*101

J'ai changé mon câble mais toujours le même problème. De plus, ces erreurs ne sont jamais au même endroit (même lignes). Puis à cause de ces erreurs le logiciels bloque l'impression à des endroits aléatoires.

Comment peut-on résoudre ce problème?

Toute aide est la bienvenue

Merci d'avance

Emeline

Repetier

Did it work until line 300 without errors?
I think either baud rate is not 100% correct or input buffer was set too high. Try 127 and if it stays 63.

Emelinej

Yes it work but sometime errors start before 300, it's random.

What is input buffer? Where I change the number to 127?

Repetier

In printer settings - it is one of the serial parameters to choose from. If it too large host will send more then printer can store causing errors during fast communication.

Emelinej

Thank you!!