What should i do when i changed my extruder from the original prusa i3 reprap printer to this:
https://www.amazon.com/Extruder-Printer-Filament-Extrusion-Aluminum/dp/B07P91BNMY
and when i try to connect it by repetier host it says like this
21:33:35.848 : Printer reset detected - initalizing
21:33:35.848 : start
21:33:35.848 : echo:Marlin 1.1.9
21:33:35.851 : echo: Last Updated: 2018-08-01 | Author: (none, default config)
21:33:35.852 : echo:Compiled: Jul 31 2019
21:33:35.855 : echo: Free Memory: 5628 PlannerBufferBytes: 1232
21:33:35.857 : echo:Hardcoded Default Settings Loaded
21:33:35.858 : echo: G21 ; (mm)
21:33:35.859 : echo:Filament settings: Disabled
21:33:35.859 : echo: M200 D3.00
21:33:35.860 : echo: M200 D0
21:33:35.860 : echo:Steps per unit:
21:33:35.863 : echo: M92 X80.00 Y80.00 Z4000.00 E500.00
21:33:35.865 : echo:Maximum feedrates (units/s):
21:33:35.866 : echo: M203 X300.00 Y300.00 Z5.00 E25.00
21:33:35.867 : echo:Maximum Acceleration (units/s2):
21:33:35.869 : echo: M201 X3000 Y3000 Z100 E10000
21:33:35.873 : echo:Acceleration (units/s2): P<print_accel> R<retract_accel> T<travel_accel>
21:33:35.874 : echo: M204 P3000.00 R3000.00 T3000.00
21:33:35.880 : echo:Advanced: Q<min_segment_time_us> S<min_feedrate> T<min_travel_feedrate> X<max_x_jerk> Y<max_y_jerk> Z<max_z_jerk> E<max_e_jerk>
21:33:35.882 : echo: M205 Q20000 S0.00 T0.00 X10.00 Y10.00 Z0.30 E5.00
21:33:35.883 : echo:Home offset:
21:33:35.884 : echo: M206 X0.00 Y0.00 Z0.00
21:33:35.885 : echo:PID settings:
21:33:35.887 : echo: M301 P22.20 I1.08 D114.00
21:33:36.050 : N1 M11034
21:33:36.050 : N2 M115*36
21:33:36.050 : N3 M10536
21:33:36.050 : N4 M114*35
21:33:36.064 : N5 M111 S698
21:33:36.064 : N6 T0*60
21:33:36.064 : N7 M2022
21:33:36.064 : N8 M80*19
21:33:36.064 : N9 M10546
21:33:36.151 : FIRMWARE_NAME:Marlin 1.1.9 (Github) SOURCE_CODE_URL:https://github.com/MarlinFirmware/Marlin PROTOCOL_VERSION:1.0 MACHINE_TYPE:3D Printer EXTRUDER_COUNT:1 UUID:cede2a2f-41a2-4748-9b12-c55c62f367ff
21:33:36.151 : N10 M220 S100*80
21:33:36.151 : Cap:SERIAL_XON_XOFF:0
21:33:36.152 : Cap:EEPROM:0
21:33:36.152 : Cap:VOLUMETRIC:1
21:33:36.154 : Cap:AUTOREPORT_TEMP:1
21:33:36.155 : Cap:PROGRESS:0
21:33:36.155 : Cap:PRINT_JOB:1
21:33:36.156 : Cap:AUTOLEVEL:0
21:33:36.156 : Cap:Z_PROBE:0
21:33:36.157 : Cap:LEVELING_DATA:0
21:33:36.158 : Cap:BUILD_PERCENT:0
21:33:36.159 : Cap:SOFTWARE_POWER:0
21:33:36.159 : Cap:TOGGLE_LIGHTS:0
21:33:36.160 : Cap:CASE_LIGHT_BRIGHTNESS:0
21:33:36.161 : Cap:EMERGENCY_PARSER:0
21:33:36.163 : Cap:AUTOREPORT_SD_STATUS:0
21:33:36.165 : Cap:THERMAL_PROTECTION:1
21:33:36.165 : N11 M221 S10080
21:33:36.173 : N12 M111 S6*84
21:33:36.174 : X:0.00 Y:0.00 Z:0.00 E:0.00 Count X:0 Y:0 Z:0
21:33:36.174 : echo:DEBUG:INFO,ERRORS
21:33:36.175 : N13 T08
21:33:36.175 : N14 M155 S1*85
21:33:36.175 : echo:Active Extruder: 0
21:33:36.176 : echo:Unknown command: "M20"
21:33:36.179 : echo:Unknown command: "M80"
21:33:36.185 : echo:DEBUG:INFO,ERRORS
21:33:36.187 : echo:Active Extruder: 0
21:33:56.451 : N15 G1 Z1 F1000
21:33:58.949 : N16 G28*36
21:34:00.798 : N17 M140 S5599
21:34:01.056 : N18 M104 T0 S200*26
21:34:01.296 : N19 M106 P0 S25529
21:34:01.856 : X:0.00 Y:0.00 Z:0.00 E:0.00 Count X:0 Y:0 Z:0
21:34:22.147 : Error:Heating failed, system stopped! Heater_ID: 0
21:34:22.147 : Error:Printer halted. kill() called!
21:34:26.688 : N20 M999*24
21:34:26.688 : N1 M110*34
21:34:27.682 : N1 M110*34
21:34:27.682 : N1 M110*34
