Ok, first 1 retracted 100, then pressed extrude 100 @ 30mm/s then the emergiency stop. This was the result:
10:35:34.332: N784766 G1 E-100.00 F1800
10:35:41.791: N784775 G1 X0.00 Y0.00 F1800
10:35:41.791: N784776 G1 Z0.00 F1800
10:35:41.791: N784777 G1 E-50.00 F1800
10:35:41.797: N784778 G1 E0.00 F1800
10:35:47.421: start
10:35:47.421: Info:PowerUp
10:35:47.421: Transformation matrix: 1.000000 0.000000 0.000000 0.000000 1.000000 0.000000 0.000000 0.000000 1.000000
10:35:47.421: Free RAM:79556
10:35:47.421: Autoretract:0
10:35:47.422: X:0.00 Y:0.00 Z:0.000 E:0.0000
10:35:47.422: SelectExtruder:0
10:35:47.422: N1 M112
10:35:47.423: M110 N0
10:35:47.423: N2 M115
10:35:47.423: N3 M220 S100
10:35:47.423: N4 M221 S100
10:35:47.423: N5 M355
10:35:47.423: N6 G92 E0
10:35:47.423: N7 M114
10:35:47.423: N8 G90
10:35:47.424: N9 M111 S6
10:35:47.424: N10 M360
10:35:47.424: N11 M539 S1
10:35:47.643: start
10:35:47.644: N2 M117 IP:192.168.2.7
10:35:47.644: M110 N0
10:35:47.644: N2 M115
10:35:47.644: N3 M220 S100
10:35:47.644: N4 M221 S100
10:35:47.644: N5 M355
10:35:47.645: N6 G92 E0
10:35:47.645: N7 M114
10:35:47.645: N8 G90
10:35:47.645: N9 M111 S6
10:35:47.645: Info:Software Reset
10:35:47.647: Transformation matrix: 1.000000 0.000000 0.000000 0.000000 1.000000 0.000000 0.000000 0.000000 1.000000
10:35:47.647: Free RAM:79556
10:35:47.648: Autoretract:0
10:35:47.648: X:0.00 Y:0.00 Z:0.000 E:0.0000
10:35:47.649: SelectExtruder:0
10:35:47.974: N10 M360
10:35:47.975: N11 M539 S1
10:35:47.977: N12 M20
10:35:47.978: N13 M117 IP:192.168.2.7
10:35:47.983: FIRMWARE_NAME:Repetier_0.92.9 FIRMWARE_URL:https://github.com/repetier/Repetier-Firmware/ PROTOCOL_VERSION:1.0 MACHINE_TYPE:Delta EXTRUDER_COUNT:1 REPETIER_PROTOCOL:3
10:35:47.984: Printed filament:2824.97m Printing time:26 days 4 hours 56 min
10:35:47.987: PrinterMode:FFF
10:35:47.991: Info:No case lights
10:35:47.991: X:0.00 Y:0.00 Z:0.000 E:0.0000
10:35:47.992: DebugLevel:6
10:35:47.993: Config:Baudrate:250000
10:35:47.994: Config:InputBuffer:127
10:35:47.994: Config:NumExtruder:1
10:35:47.994: Config:MixingExtruder:0
10:35:47.994: Config:HeatedBed:1
10:35:47.999: Config:SDCard:1
10:35:47.999: Config:Fan:1
10:35:48.000: Config:Fan2:0
10:35:48.000: Config:LCD:0
10:35:48.000: Config:SoftwarePowerSwitch:0
10:35:48.000: Config:XHomeDir:-1
10:35:48.001: Config:YHomeDir:-1
10:35:48.002: Config:ZHomeDir:1
10:35:48.002: Config:SupportG10G11:0
10:35:48.008: Config:SupportLocalFilamentchange:0
10:35:48.008: Config:CaseLights:0
10:35:48.008: Config:ZProbe:0
10:35:48.008: Config:Autolevel:1
10:35:48.008: Config:EEPROM:1
10:35:48.009: Config:PrintlineCache:16
10:35:48.009: Config:JerkXY:20.00
10:35:48.010: Config:XMin:0.00
10:35:48.011: Config:YMin:0.00
10:35:48.011: Config:ZMin:0.00
10:35:48.011: Config:XMax:200.00
10:35:48.016: Config:YMax:200.00
10:35:48.016: Config:ZMax:394.10
10:35:48.016: Config:XSize:200.00
10:35:48.017: Config:YSize:200.00
10:35:48.017: Config:ZSize:394.10
10:35:48.017: Config:XPrintAccel:1000.00
10:35:48.019: Config:YPrintAccel:1000.00
10:35:48.019: Config:ZPrintAccel:1000.00
10:35:48.024: Config:XTravelAccel:1000.00
10:35:48.024: Config:YTravelAccel:1000.00
10:35:48.025: Config:ZTravelAccel:1000.00
10:35:48.025: Config:PrinterType:Delta
10:35:48.025: Config:MaxBedTemp:120
10:35:48.026: Config:Extr.1:Jerk:20.00
10:35:48.027: Config:Extr.1:MaxSpeed:50.00
10:35:48.027: Config:Extr.1:Acceleration:5000.00
10:35:48.032: Config:Extr.1:Diameter:0.00
10:35:48.033: Config:Extr.1:MaxTemp:275
10:35:48.033: Unknown command:N11 M539 S1
10:35:48.034: Begin file list
xxx
10:35:48.276: End file list
