Teacup firmware problem with Temp thermiston in Repetier-Host

caslor

Hi
i am experimenting with teacup firmware and uno board
The problem is that Repetier-Host doesn't saw the extruder temp... is always 0c

in the other hand when i connect my board to Pronterface i am getting the right readings

also when i send the M105 command in the Repetier nothing happens

any Help

Thanks in advance

Repetier

What does teacup return on M105 exactly? I guess it is just not returning the expected format.

caslor

As I can remember (I am not in the pc right now to confirm it) it doesn't return nothing..

Also I remember that when I connect the board to Repetier-Host it says bad M command 111,
bad M command 80
bad M command 20

I will check them all the above later day that I will be infront the machine

Repetier

M111/M80/M20 are not important so no harm here. But for M105 the return format needs to be known exactly to help here.

caslor

Hi
This is from the log in Repetier-host. As i can see it can read the temperature right in the log but doesnt display it in the ''manual control'' graphic panel where the extruder is

'' 08:21:55.440 : start
08:21:55.552 : N1 M11034
08:21:55.552 : N2 M11536
08:21:55.552 : N3 M10536
08:21:55.553 : N4 M11435
08:21:55.563 : ok
08:21:55.563 : ok
08:21:55.566 : N5 M111 S698
08:21:55.567 : N6 T060
08:21:55.567 : N7 M2022
08:21:55.568 : N8 M8019
08:21:55.568 : N9 M10546
08:21:55.590 : N10 M111 S686
08:21:55.590 : ok
08:21:55.590 : ok
08:21:55.590 : N11 T010
08:21:55.595 : T:0.0/0.0
08:21:55.595 : ok
08:21:55.595 : ok
08:21:55.600 : ok
08:21:55.600 : ok
08:21:55.606 : ok
08:21:55.606 : ok
08:21:55.607 : ok
08:21:55.607 : ok
08:21:55.611 : ok
08:21:55.611 : ok
08:21:55.616 : rs N8 Expected checksum 97
08:21:55.616 : ok
08:21:55.616 : ok
08:21:55.616 : ok
08:21:55.621 : ok
08:21:55.621 : ok
08:21:58.653 : N12 M10520
08:21:58.662 : T:22.50/0.0
08:21:58.663 : ok
08:21:58.663 : ok
08:22:01.654 : N13 M10521
08:22:01.664 : T:22.0/0.0
08:22:01.664 : ok
08:22:01.664 : ok
08:22:04.656 : N14 M10518
08:22:04.665 : T:21.50/0.0
08:22:04.665 : ok
08:22:04.665 : ok
08:22:07.658 : N15 M10519
08:22:07.667 : T:22.50/0.0
08:22:07.667 : ok
08:22:07.667 : ok
08:22:10.659 : N16 M10516
08:22:10.668 : T:23.25/0.0
08:22:10.669 : ok
08:22:10.669 : ok
08:22:13.661 : N17 M10517
08:22:13.670 : T:23.25/0.0
08:22:13.670 : ok
08:22:13.670 : ok
08:22:16.663 : N18 M10530
08:22:16.672 : T:23.25/0.0
08:22:16.672 : ok
08:22:16.672 : ok
08:22:19.665 : N19 M10531
08:22:19.675 : T:23.25/0.0
08:22:19.675 : ok
08:22:19.675 : ok
08:22:22.667 : N20 M10521
08:22:22.675 : T:22.50/0.0
08:22:22.675 : ok
08:22:22.676 : ok
08:22:24.972 : N21 M10520
08:22:24.983 : T:23.25/0.0
08:22:24.983 : ok
08:22:24.983 : ok
08:22:25.668 : N22 M10523
08:22:25.677 : T:23.25/0.0
08:22:25.677 : ok
08:22:25.678 : ok
08:22:28.670 : N23 M10522
08:22:28.679 : T:22.50/0.0
08:22:28.679 : ok
08:22:28.679 : ok
08:22:31.672 : N24 M10517
08:22:31.682 : T:23.25/0.0
08:22:31.682 : ok
08:22:31.682 : ok
08:22:34.673 : N25 M10516
08:22:34.683 : T:23.25/0.0
08:22:34.683 : ok
08:22:34.683 : ok
08:22:37.675 : N26 M10519
08:22:37.684 : T:23.25/0.0
08:22:37.684 : ok
08:22:37.685 : ok
08:22:40.678 : N27 M10518
08:22:40.688 : T:23.25/0.0
08:22:40.688 : ok
08:22:40.688 : ok
08:22:43.679 : N28 M10529
08:22:43.690 : T:23.25/0.0
08:22:43.690 : ok
08:22:43.690 : ok
08:22:46.682 : N29 M10528
08:22:46.691 : T:22.0/0.0
08:22:46.691 : ok
08:22:46.691 : ok
08:22:49.683 : N30 M10520
08:22:49.693 : T:19.75/0.0
08:22:49.693 : ok
08:22:49.693 : ok
08:22:52.685 : N31 M105*21
08:22:52.694 : T:22.0/0.0
08:22:52.694 : ok
08:22:52.695 : ok

''

Repetier

Very dense. I see it omits the space before / with target value. So temperature is 22.0/0.0 which is not a number.

caslor

This is the result from pronterface when i send M105

''>>> m105
SENDING:M105
T:21.50/0.0

''

and here if i place a target for the hotend

''
Setting hotend temperature to 185.000000 degrees Celsius.
>>> m105
SENDING:M105
T:22.50/185.0

''

caslor

and here is what i am getting in repetier log when i place a target temperature for the extruder (without having connected the heater element, that is why the temperature doesnt rise up )

''

10:28:18.778 : ok
10:28:20.670 : N17 M104 T0 S20021
10:28:20.679 : ok
10:28:20.679 : ok
10:28:21.769 : N18 M10530
10:28:21.778 : T:24.25/200.0
10:28:21.778 : ok
10:28:21.778 : ok
10:28:24.770 : N19 M10531
10:28:24.780 : T:23.75/200.0
10:28:24.780 : ok
10:28:24.781 : ok
10:28:27.772 : N20 M10521
10:28:27.782 : T:23.25/200.0
10:28:27.782 : ok
10:28:27.782 : ok
10:28:30.775 : N21 M10520
10:28:30.783 : T:23.25/200.0
10:28:30.784 : ok
10:28:30.784 : ok
10:28:33.777 : N22 M10523
10:28:33.788 : T:22.50/200.0
10:28:33.788 : ok
10:28:33.788 : ok
10:28:36.778 : N23 M105*22
10:28:36.788 : T:23.25/200.0

''

But still i dont get no graphical readings in the ''manual control'' panel

Repetier

As I said host does not understand it only knows it has set temperature. If you can add a space so that
T:23.25/200.0
becomes
T:23.25 /200.0

then it shoudl show graph. SHould be not hard to add the space in teacup. For next release I try to read also the wrong(non standard) output format.

caslor

Thanks for the help :)

even i dont have any background of studies in programming i manage to find the right file and alter the code

now thanks to your help the repetier host can read the values :)

this is a post for feature reference if any one has the same problem

the file that should open in an editor in the teacup folder is the ''temp.c''

and in the line 619-620 :
''
#ifdef REPORT_TARGET_TEMPS
sersendf_P(PSTR("/"));
''

have to add a space before /

be like that :

''
#ifdef REPORT_TARGET_TEMPS
sersendf_P(PSTR(" /"));
''

then compile and will work just fine :)

Repetier

Meanwhile I have fixed the issue as well for next host release. Then both solution swill work.