Configuration tool for version 1.0.0dev doesn't compile any more?!

MAKA

I tried different settings (with zprobe and without) and also started from scratch without uploading an existing configuration.h file. Always downloaded the entire zip file at the configuration tool and get following fault when I compile it.

Arduino: 1.0.6 (Windows NT (10 Pro)), Board: "Arduino Mega 2560 or Mega ADK"

In file included from /Repetier.h:1048,

from BedLeveling.cpp:107:

Drivers.h:105: error: ISO C++ forbids initialization of member 'position'

Drivers.h:105: error: making 'position' static

Drivers.h:105: error: ISO C++ forbids in-class initialization of non-const static member 'position'

BedLeveling.cpp: In static member function 'static bool Printer::startProbing(bool)':

BedLeveling.cpp:472: error: 'deltaMaxRadius' is not a member of 'EEPROM'

Two days ago it was working though. Has there been a change?

Thanks for any input.

Martin

Copied the relevant portion of Configuration.h below.

// ################ Endstop configuration #####################

#define MULTI_ZENDSTOP_HOMING 0

#define ENDSTOP_PULLUP_X_MIN true

#define ENDSTOP_X_MIN_INVERTING false

#define MIN_HARDWARE_ENDSTOP_X true

#define ENDSTOP_PULLUP_Y_MIN true

#define ENDSTOP_Y_MIN_INVERTING false

#define MIN_HARDWARE_ENDSTOP_Y true

#define ENDSTOP_PULLUP_Z_MIN true

#define ENDSTOP_Z_MIN_INVERTING true

#define MIN_HARDWARE_ENDSTOP_Z true

#define ENDSTOP_PULLUP_Z2_MINMAX true

#define ENDSTOP_Z2_MINMAX_INVERTING false

#define MINMAX_HARDWARE_ENDSTOP_Z2 false

#define ENDSTOP_PULLUP_X_MAX true

#define ENDSTOP_X_MAX_INVERTING false

#define MAX_HARDWARE_ENDSTOP_X false

#define ENDSTOP_PULLUP_Y_MAX true

#define ENDSTOP_Y_MAX_INVERTING false

#define MAX_HARDWARE_ENDSTOP_Y false

#define ENDSTOP_PULLUP_Z_MAX true

#define ENDSTOP_Z_MAX_INVERTING false

#define MAX_HARDWARE_ENDSTOP_Z false

#define max_software_endstop_r true

#define min_software_endstop_x false

#define min_software_endstop_y false

#define min_software_endstop_z false

#define max_software_endstop_x true

#define max_software_endstop_y true

#define max_software_endstop_z true

#define DOOR_PIN -1

#define DOOR_PULLUP 1

#define DOOR_INVERTING 0

#define ENDSTOP_X_BACK_MOVE 5

#define ENDSTOP_Y_BACK_MOVE 5

#define ENDSTOP_Z_BACK_MOVE 2

#define ENDSTOP_X_RETEST_REDUCTION_FACTOR 3

#define ENDSTOP_Y_RETEST_REDUCTION_FACTOR 3

#define ENDSTOP_Z_RETEST_REDUCTION_FACTOR 3

#define ENDSTOP_X_BACK_ON_HOME 0

#define ENDSTOP_Y_BACK_ON_HOME 0

#define ENDSTOP_Z_BACK_ON_HOME 0

#define ALWAYS_CHECK_ENDSTOPS 0

#define MOVE_X_WHEN_HOMED 0

#define MOVE_Y_WHEN_HOMED 0

#define MOVE_Z_WHEN_HOMED 0

// ################# XYZ movements ###################

#define X_ENABLE_ON 0

#define Y_ENABLE_ON 0

#define Z_ENABLE_ON 0

#define DISABLE_X 0

#define DISABLE_Y 0

#define DISABLE_Z 0

#define DISABLE_E 0

#define INVERT_X_DIR 1

#define INVERT_Y_DIR 1

#define INVERT_Z_DIR 1

#define X_HOME_DIR -1

#define Y_HOME_DIR -1

#define Z_HOME_DIR -1

#define X_MAX_LENGTH 255

#define Y_MAX_LENGTH 205

#define Z_MAX_LENGTH 225

#define X_MIN_POS 0

#define Y_MIN_POS 0

#define Z_MIN_POS 0

#define Z2_MINMAX_PIN -1

#define DISTORTION_CORRECTION 1

#define DISTORTION_CORRECTION_POINTS 5

#define DISTORTION_CORRECTION_R 100

#define DISTORTION_PERMANENT 1

#define DISTORTION_UPDATE_FREQUENCY 15

#define DISTORTION_START_DEGRADE 0.5

#define DISTORTION_END_HEIGHT 2

#define DISTORTION_EXTRAPOLATE_CORNERS 0

#define DISTORTION_XMIN 0

#define DISTORTION_YMIN 40

#define DISTORTION_XMAX 250

#define DISTORTION_YMAX 200

// ##########################################################################################

// ## Movement settings ##

// ##########################################################################################

#define FEATURE_BABYSTEPPING 1

#define BABYSTEP_MULTIPLICATOR 4

#define DELTA_SEGMENTS_PER_SECOND_PRINT 180 // Move accurate setting for print moves

#define DELTA_SEGMENTS_PER_SECOND_MOVE 70 // Less accurate setting for other moves

#define EXACT_DELTA_MOVES 1

// Delta settings

#define DELTA_HOME_ON_POWER 0

#define DELTASEGMENTS_PER_PRINTLINE 20

#define STEPPER_INACTIVE_TIME 360L

#define MAX_INACTIVE_TIME 0L

#define MAX_FEEDRATE_X 200

#define MAX_FEEDRATE_Y 200

#define MAX_FEEDRATE_Z 5

#define HOMING_FEEDRATE_X 50

#define HOMING_FEEDRATE_Y 50

#define HOMING_FEEDRATE_Z 3

#define HOMING_ORDER HOME_ORDER_XYTZ

#define ZHOME_PRE_RAISE 1

#define ZHOME_PRE_RAISE_DISTANCE 4

#define ZHOME_MIN_TEMPERATURE 0

#define ZHOME_HEAT_ALL 0

#define ZHOME_HEAT_HEIGHT 5

#define ZHOME_X_POS 120

#define ZHOME_Y_POS 100

#define ENABLE_BACKLASH_COMPENSATION 0

#define X_BACKLASH 0

#define Y_BACKLASH 0

#define Z_BACKLASH 0

#define RAMP_ACCELERATION 1

#define STEPPER_HIGH_DELAY 0

#define DIRECTION_DELAY 0

#define STEP_DOUBLER_FREQUENCY 12000

#define ALLOW_QUADSTEPPING 1

#define DOUBLE_STEP_DELAY 1 // time in microseconds

#define MAX_ACCELERATION_UNITS_PER_SQ_SECOND_X 1750

#define MAX_ACCELERATION_UNITS_PER_SQ_SECOND_Y 1750

#define MAX_ACCELERATION_UNITS_PER_SQ_SECOND_Z 100

#define MAX_TRAVEL_ACCELERATION_UNITS_PER_SQ_SECOND_X 1750

#define MAX_TRAVEL_ACCELERATION_UNITS_PER_SQ_SECOND_Y 1750

#define MAX_TRAVEL_ACCELERATION_UNITS_PER_SQ_SECOND_Z 100

#define INTERPOLATE_ACCELERATION_WITH_Z 0

#define ACCELERATION_FACTOR_TOP 100

#define MAX_JERK 12.5

#define MAX_ZJERK 0.3

#define PRINTLINE_CACHE_SIZE 32

#define MOVE_CACHE_LOW 10

#define LOW_TICKS_PER_MOVE 250000

#define EXTRUDER_SWITCH_XY_SPEED 100

#define DUAL_X_AXIS 0

#define DUAL_X_RESOLUTION 0

#define X2AXIS_STEPS_PER_MM 100

#define FEATURE_TWO_XSTEPPER 0

#define X2_STEP_PIN ORIG_E1_STEP_PIN

#define X2_DIR_PIN ORIG_E1_DIR_PIN

#define X2_ENABLE_PIN ORIG_E1_ENABLE_PIN

#define FEATURE_TWO_YSTEPPER 0

#define Y2_STEP_PIN ORIG_E1_STEP_PIN

#define Y2_DIR_PIN ORIG_E1_DIR_PIN

#define Y2_ENABLE_PIN ORIG_E1_ENABLE_PIN

#define FEATURE_TWO_ZSTEPPER 0

#define Z2_STEP_PIN ORIG_E1_STEP_PIN

#define Z2_DIR_PIN ORIG_E1_DIR_PIN

#define Z2_ENABLE_PIN ORIG_E1_ENABLE_PIN

#define FEATURE_THREE_ZSTEPPER 0

#define Z3_STEP_PIN ORIG_E2_STEP_PIN

#define Z3_DIR_PIN ORIG_E2_DIR_PIN

#define Z3_ENABLE_PIN ORIG_E2_ENABLE_PIN

#define FEATURE_FOUR_ZSTEPPER 0

#define Z4_STEP_PIN ORIG_E3_STEP_PIN

#define Z4_DIR_PIN ORIG_E3_DIR_PIN

#define Z4_ENABLE_PIN ORIG_E3_ENABLE_PIN

#define FEATURE_DITTO_PRINTING 0

#define USE_ADVANCE 1

#define ENABLE_QUADRATIC_ADVANCE 1

// #################### Z-Probing #####################

#define Z_PROBE_Z_OFFSET 0

#define Z_PROBE_Z_OFFSET_MODE 0

#define UI_BED_COATING 1

#define FEATURE_Z_PROBE 1

#define EXTRUDER_IS_Z_PROBE 0

#define Z_PROBE_BED_DISTANCE 2

#define Z_PROBE_PIN 45

#define Z_PROBE_PULLUP 0

#define Z_PROBE_ON_HIGH 1

#define Z_PROBE_X_OFFSET -7

#define Z_PROBE_Y_OFFSET 40

#define Z_PROBE_WAIT_BEFORE_TEST 0

#define Z_PROBE_SPEED 2

#define Z_PROBE_XY_SPEED 150

#define Z_PROBE_SWITCHING_DISTANCE 0.8

#define Z_PROBE_REPETITIONS 2

#define Z_PROBE_HEIGHT 3.2

#define Z_PROBE_START_SCRIPT ""

#define Z_PROBE_FINISHED_SCRIPT ""

#define Z_PROBE_RUN_AFTER_EVERY_PROBE ""

#define Z_PROBE_REQUIRES_HEATING 0

#define Z_PROBE_MIN_TEMPERATURE 150

#define FEATURE_AUTOLEVEL 1

#define FEATURE_SOFTWARE_LEVELING 0

#define Z_PROBE_X1 10

#define Z_PROBE_Y1 40

#define Z_PROBE_X2 250

#define Z_PROBE_Y2 40

#define Z_PROBE_X3 10

#define Z_PROBE_Y3 200

#define BED_LEVELING_METHOD 0

#define BED_CORRECTION_METHOD 0

#define BED_LEVELING_GRID_SIZE 5

#define BED_LEVELING_REPETITIONS 5

#define BED_MOTOR_1_X 0

#define BED_MOTOR_1_Y 0

#define BED_MOTOR_2_X 200

#define BED_MOTOR_2_Y 0

#define BED_MOTOR_3_X 100

#define BED_MOTOR_3_Y 200

#define BENDING_CORRECTION_A 0

#define BENDING_CORRECTION_B 0

#define BENDING_CORRECTION_C 0

#define FEATURE_AXISCOMP 1

#define AXISCOMP_TANXY 0

#define AXISCOMP_TANYZ 0

#define AXISCOMP_TANXZ 0

MAKA

Nobody else having this problem with 1.0.0 dev?

I might have found the root cause. Looked up my last version that was working from 4 days ago and found in the new version following lines that were different

Drivers.h

int32_t position = 0;

Bed_leveling.cpp

#if DRIVE_SYSTEM == DELA

When I change it to

int32_t position

#if DRIVE_SYSTEM == DELTA

it compiles. Haven't uploaded and tested it yet.

Repetier

Thanks for the hint. Have fixed it now. Not sure why it compiled for me correctly for delta.

The position = 0 initialization should be no problem with recent compilers, but I have changed it back to initialization in constructor for old C++ compilers. So now it should compile fine.

MAKA

Thanks, that was quick.