Z Probing coming up with an error

PAd1A

<div>Hey.

I do everything according to instructions http://www.repetier.com/documentation/repetier-firmware/z-probing .

When you enter a command G29 or G32 or G33

I receive an error

</div>

22:05:38.020 : Error:Bpos x square

22:05:38.021 : Warning:Invalid delta coordinate - move ignored x:-4880 y:9739 z:102

22:05:38.021 : Warning:in queueDeltaMove to calculateDeltaSubSegments returns error.

22:05:38.021 : Warning:moveToReal / queueDeltaMove returns error

Please help me.

Repetier

Your probing positions are outside allowed coordinates. Target position + z probe offset must be a allowed position or you get that message. Normally beacause you placed then too close to your towers where the offset then makes it invalid.

PAd1A

The extruder is exactly in the middle.

Or home position

Error does not disappear

Repetier

And what have you done to remove the error? Have you moved probing position? How did you test exactly.

PAd1A

I'm asking you what to do.

I do not understand. Write the points please.

Here is my configuration EEPROM

PAd1A

0 Language 115200 Baudrate 0.021 Filament printed [m] 372 Printer active [s] 0 Max. inactive time [ms,0=off] 360000 Stop stepper after inactivity [ms,0=off] 100.0000 Steps per mm 200.000 Max. feedrate [mm/s] 40.000 Homing feedrate [mm/s] 20.000 Max. jerk [mm/s] -90.000 X min pos [mm] -90.000 Y min pos [mm] 0.000 Z min pos [mm] 90.000 X max length [mm] 90.000 Y max length [mm] 225.780 Z max length [mm] 1000.000 Acceleration [mm/s²] 1000.000 Travel acceleration [mm/s²] 200.000 Diagonal rod length [mm] 100.000 Horizontal rod radius at 0[mm] 95.000 Max printable radius [mm] 70 Segments/s for travel 180 Segments/s for printing 20 Tower X endstop offset [steps] 0 Tower Y endstop offset [steps] 40 Tower Z endstop offset [steps] 210.000 Alpha A(210): 330.000 Alpha B(330): 90.000 Alpha C(90): 0.000 Delta Radius A(0): 0.000 Delta Radius B(0): 0.000 Delta Radius C(0): 0.000 Corr. diagonal A [mm] 0.000 Corr. diagonal B [mm] 0.000 Corr. diagonal C [mm] 0.000 Coating thickness [mm] 0.000 Z-probe height [mm] 10.000 Max. z-probe - bed dist.[mm] 2.000 Z-probe speed [mm/s] 150.000 Z-probe x-y-speed [mm/s] 0.000 Z-probe offset x [mm] 0.000 Z-probe offset y [mm] -69.280 Z-probe X1 [mm] -40.000 Z-probe Y1 [mm] 69.280 Z-probe X2 [mm] -40.000 Z-probe Y2 [mm] -69.280 Z-probe X3 [mm] 40.000 Z-probe Y3 [mm] 0.000 Z-probe bending correction A [mm] 0.000 Z-probe bending correction B [mm] 0.000 Z-probe bending correction C [mm] 0 Autolevel active (1/0) 0.000 tanXY Axis Compensation 0.000 tanYZ Axis Compensation 0.000 tanXZ Axis Compensation 1 Bed Heat Manager [0-3] 190 Bed PID drive max 80 Bed PID drive min 196.000 Bed PID P-gain 33.000 Bed PID I-gain 290.000 Bed PID D-gain 190 Bed PID max value [0-255] 0 Enable retraction conversion [0/1] 2.000 Retraction length [mm] 40.000 Retraction speed [mm/s] 1.000 Retraction z-lift [mm] 0.000 Extra extrusion on undo retract[mm] 20.000 Retraction undo speed 104.000 Extr.1 steps per mm 50.000 Extr.1 max. feedrate [mm/s] 20.000 Extr.1 start feedrate [mm/s] 5000.000 Extr.1 acceleration [mm/s²] 1 Extr.1 heat manager [0-3] 230 Extr.1 PID drive max 40 Extr.1 PID drive min 7.0000 Extr.1 PID P-gain/dead-time 2.0000 Extr.1 PID I-gain 40.0000 Extr.1 PID D-gain 230 Extr.1 PID max value [0-255] 0 Extr.1 X-offset [steps] 0 Extr.1 Y-offset [steps] 0 Extr.1 Z-offset [steps] 1 Extr.1 temp. stabilize time [s] 150 Extr.1 temp. for retraction whenheating [C] 0 Extr.1 distance to retract whenheating [mm] 255 Extr.1 extruder cooler speed [0-255]

Repetier

Warning:Invalid delta coordinate - move ignored x:-4880 y:9739 z:102

with 100 steps per mm is coordinate x=-48,8, y = 97,39, z = 1.02 which is outside the horizontal radius of 95mm you defined. So the error message is correct.

I wonder why this appears on G32 as your probing points are different coordinates. So provide a log with commands and return data of what you exactly entered. Normally you just say G32 S2 and it homes, goes down and then to probing points. These coordinates are never reached even if used as a grid.