Problem after Installation (delta Printer) (0.92)

lildann514

I recently upgrade my chiness delta printer with a Ramp 1.4/Arduino mega 2560 /a988 stepper/Mechanical endstop

After many hours to config my endstop, i sucess to make the homing in the max position with no problem... but when im connect the printer to repetier host the printer remake is homing and after that the software say me the printer ask for a pause and when im click on continu the printer go down and dont stop ...... with the M119 command all my endstop is on L and when im push one is go H

im just out off idea ...... here my config .... for notice is not yet calibrated

// ################ Endstop configuration #####################

#define ENDSTOP_PULLUP_X_MIN true

#define ENDSTOP_X_MIN_INVERTING false

#define MIN_HARDWARE_ENDSTOP_X false

#define ENDSTOP_PULLUP_Y_MIN true

#define ENDSTOP_Y_MIN_INVERTING false

#define MIN_HARDWARE_ENDSTOP_Y false

#define ENDSTOP_PULLUP_Z_MIN true

#define ENDSTOP_Z_MIN_INVERTING false

#define MIN_HARDWARE_ENDSTOP_Z false

#define ENDSTOP_PULLUP_X_MAX true

#define ENDSTOP_X_MAX_INVERTING false

#define MAX_HARDWARE_ENDSTOP_X true

#define ENDSTOP_PULLUP_Y_MAX true

#define ENDSTOP_Y_MAX_INVERTING false

#define MAX_HARDWARE_ENDSTOP_Y true

#define ENDSTOP_PULLUP_Z_MAX true

#define ENDSTOP_Z_MAX_INVERTING false

#define MAX_HARDWARE_ENDSTOP_Z true

#define max_software_endstop_r true

#define min_software_endstop_x true

#define min_software_endstop_y true

#define min_software_endstop_z true

#define max_software_endstop_x false

#define max_software_endstop_y false

#define max_software_endstop_z false

#define ENDSTOP_X_BACK_MOVE 5

#define ENDSTOP_Y_BACK_MOVE 5

#define ENDSTOP_Z_BACK_MOVE 4

#define ENDSTOP_X_RETEST_REDUCTION_FACTOR 3

#define ENDSTOP_Y_RETEST_REDUCTION_FACTOR 3

#define ENDSTOP_Z_RETEST_REDUCTION_FACTOR 3

#define ENDSTOP_X_BACK_ON_HOME 1

#define ENDSTOP_Y_BACK_ON_HOME 1

#define ENDSTOP_Z_BACK_ON_HOME 0

#define ALWAYS_CHECK_ENDSTOPS 1

// ################# XYZ movements ###################

#define X_ENABLE_ON 0

#define Y_ENABLE_ON 0

#define Z_ENABLE_ON 0

#define DISABLE_X 0

#define DISABLE_Y 0

#define DISABLE_Z 0

#define DISABLE_E 0

#define INVERT_X_DIR -1

#define INVERT_Y_DIR -1

#define INVERT_Z_DIR -1

#define X_HOME_DIR -1

#define Y_HOME_DIR -1

#define Z_HOME_DIR -1

#define X_MAX_LENGTH 200

#define Y_MAX_LENGTH 200

#define Z_MAX_LENGTH 180

#define X_MIN_POS -1

#define Y_MIN_POS -1

#define Z_MIN_POS -1

#define DISTORTION_CORRECTION 0

#define DISTORTION_CORRECTION_POINTS 5

#define DISTORTION_CORRECTION_R 100

#define DISTORTION_PERMANENT 1

#define DISTORTION_UPDATE_FREQUENCY 15

#define DISTORTION_START_DEGRADE 0.5

#define DISTORTION_END_HEIGHT 1

#define DISTORTION_EXTRAPOLATE_CORNERS 0

// ##########################################################################################

// ## Movement settings ##

// ##########################################################################################

#define FEATURE_BABYSTEPPING 1

#define BABYSTEP_MULTIPLICATOR 1

#define DELTA_SEGMENTS_PER_SECOND_PRINT 180 // Move accurate setting for print moves

#define DELTA_SEGMENTS_PER_SECOND_MOVE 75 // Less accurate setting for other moves

#define EXACT_DELTA_MOVES 1

// Delta settings

#define DELTA_DIAGONAL_ROD 180 // mm

#define DELTA_ALPHA_A 210

#define DELTA_ALPHA_B 330

#define DELTA_ALPHA_C 90

#define DELTA_RADIUS_CORRECTION_A 0

#define DELTA_RADIUS_CORRECTION_B 0

#define DELTA_RADIUS_CORRECTION_C 0

#define DELTA_DIAGONAL_CORRECTION_A 0

#define DELTA_DIAGONAL_CORRECTION_B 0

#define DELTA_DIAGONAL_CORRECTION_C 0

#define END_EFFECTOR_HORIZONTAL_OFFSET 0

#define CARRIAGE_HORIZONTAL_OFFSET 0

#define DELTA_MAX_RADIUS 125

#define ROD_RADIUS 85

#define PRINTER_RADIUS 85

#define DELTA_HOME_ON_POWER 0

#define STEP_COUNTER

#define DELTA_X_ENDSTOP_OFFSET_STEPS 0

#define DELTA_Y_ENDSTOP_OFFSET_STEPS 0

#define DELTA_Z_ENDSTOP_OFFSET_STEPS 0

#define DELTA_FLOOR_SAFETY_MARGIN_MM 15

//#define SOFTWARE_LEVELING

#define DELTASEGMENTS_PER_PRINTLINE 24

#define STEPPER_INACTIVE_TIME 360L

#define MAX_INACTIVE_TIME 0L

#define MAX_FEEDRATE_X 250

#define MAX_FEEDRATE_Y 250

#define MAX_FEEDRATE_Z 250

#define HOMING_FEEDRATE_X 30

#define HOMING_FEEDRATE_Y 30

#define HOMING_FEEDRATE_Z 300

#define HOMING_ORDER HOME_ORDER_ZXY

#define ZHOME_MIN_TEMPERATURE 0

#define ZHOME_HEAT_ALL 1

#define ZHOME_HEAT_HEIGHT 20

#define ZHOME_X_POS 999999

#define ZHOME_Y_POS 999999

#define ENABLE_BACKLASH_COMPENSATION 0

#define X_BACKLASH 0

#define Y_BACKLASH 0

#define Z_BACKLASH 0

#define RAMP_ACCELERATION 1

#define STEPPER_HIGH_DELAY 0

#define DIRECTION_DELAY 2

#define STEP_DOUBLER_FREQUENCY 12000

#define ALLOW_QUADSTEPPING 1

#define DOUBLE_STEP_DELAY 2 // time in microseconds

#define MAX_ACCELERATION_UNITS_PER_SQ_SECOND_X 120

#define MAX_ACCELERATION_UNITS_PER_SQ_SECOND_Y 120

#define MAX_ACCELERATION_UNITS_PER_SQ_SECOND_Z 120

#define MAX_TRAVEL_ACCELERATION_UNITS_PER_SQ_SECOND_X 120

#define MAX_TRAVEL_ACCELERATION_UNITS_PER_SQ_SECOND_Y 120

#define MAX_TRAVEL_ACCELERATION_UNITS_PER_SQ_SECOND_Z 120

#define INTERPOLATE_ACCELERATION_WITH_Z 3

#define ACCELERATION_FACTOR_TOP 100

#define MAX_JERK 18

#define MAX_ZJERK 0.3

#define PRINTLINE_CACHE_SIZE 16

#define MOVE_CACHE_LOW 10

#define LOW_TICKS_PER_MOVE 250000

#define FEATURE_TWO_XSTEPPER 0

#define X2_STEP_PIN ORIG_E1_STEP_PIN

#define X2_DIR_PIN ORIG_E1_DIR_PIN

#define X2_ENABLE_PIN ORIG_E1_ENABLE_PIN

#define FEATURE_TWO_YSTEPPER 0

#define Y2_STEP_PIN ORIG_E1_STEP_PIN

#define Y2_DIR_PIN ORIG_E1_DIR_PIN

#define Y2_ENABLE_PIN ORIG_E1_ENABLE_PIN

#define FEATURE_TWO_ZSTEPPER 0

#define Z2_STEP_PIN ORIG_E1_STEP_PIN

#define Z2_DIR_PIN ORIG_E1_DIR_PIN

#define Z2_ENABLE_PIN ORIG_E1_ENABLE_PIN

#define FEATURE_THREE_ZSTEPPER 0

#define Z3_STEP_PIN ORIG_E2_STEP_PIN

#define Z3_DIR_PIN ORIG_E2_DIR_PIN

#define Z3_ENABLE_PIN ORIG_E2_ENABLE_PIN

#define FEATURE_DITTO_PRINTING 0

#define USE_ADVANCE 0

#define ENABLE_QUADRATIC_ADVANCE 0

// ################# Misc. settings ##################

#define BAUDRATE 250000

#define ENABLE_POWER_ON_STARTUP 1

#define POWER_INVERTING 0

#define KILL_METHOD 1

#define ACK_WITH_LINENUMBER 1

#define WAITING_IDENTIFIER "wait"

#define ECHO_ON_EXECUTE 1

#define EEPROM_MODE 1

#undef PS_ON_PIN

#define PS_ON_PIN -1

#define JSON_OUTPUT 0

Repetier

It is a firmware bug. Please update to the now available fixed firmware version.

lildann514

My god thank!!!! im not crazy XD